Intel Celeron Dual-Core E1000 Series Скачать руководство пользователя страница 107 | Manualshive

Страница: 107 / 148

background image

Case Temperature Reference Metrology

Thermal and Mechanical Design Guidelines

107

Figure

7-35. Removing Excess Adhesive from IHS

39.

Using a blade, carefully shave any adhesive that is above the IHS surface (see
Figure

7-35). The preferred method is to shave from the edge to the center of the

IHS.

Note:

The adhesive shaving step should be performed while the adhesive is partially cured,
but still soft. This will help to keep the adhesive surface flat and smooth with no pits
or voids. If there are voids in the adhesive, refill the voids with adhesive and shave a
second time.

40.

Clean IHS surface with IPA and a wipe.

41.

Clean the LGA pads with IPA and a wipe.

42.

Replace the land side cover on the device.

43.

Perform a final continuity test.

44.

Wind the thermocouple wire into loops and secure or if provided by the vendor
back onto the plastic roll (see Figure

Figure

7-36. Finished Thermocouple Installation

«
...
105
106
107
108
109
...
»

Содержание Celeron Dual-Core E1000 Series





















































































































































Отзывы:

Нет отзывов

Похожие инструкции для Celeron Dual-Core E1000 Series

Бренд: TC-Helicon Страницы: 2

Бренд: Cypress Semiconductor Страницы: 11

Бренд: RAK Страницы: 30

Бренд: Moxa Technologies Страницы: 2

Бренд: Giacomini Страницы: 2

Бренд: Nakayo Страницы: 119

Бренд: Powerleap Страницы: 28

Бренд: Lindy Страницы: 12

Бренд: Icy Box Страницы: 2

Бренд: Intel Страницы: 44

NexXxoS GPX-N 1070-M08

Бренд: Alphacool Страницы: 4

Xtreme Networked Boat

Бренд: Broadband Products Страницы: 16

Бренд: SilverStone Страницы: 16

WISENET XRN-1610

Бренд: Hanwha Techwin Страницы: 88

ST7-EMU3 Series

Бренд: ST Страницы: 39

Бренд: Iomega Страницы: 32

Бренд: Geekworm Страницы: 10

MS-9A95 WindBOX IV Advanced

Бренд: MSI Страницы: 51

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды