Intel Celeron Dual-Core E1000 Series Скачать руководство пользователя страница 106

Страница: 106 / 148

Case Temperature Reference Metrology

106

Thermal and Mechanical Design Guidelines

36.

Clean the surface of the IHS with Alcohol and use compressed air to remove any

remaining contaminants.

37.

Fill the rest of the groove with Loctite* 498 Adhesive. Verify under the microscope

that the thermocouple wire is below the surface along the entire length of the IHS
groove (see Figure

7-33).

Figure

7-33. Filling Groove with Adhesive

38.

To speed up the curing process apply Loctite* Accelerator on top of the Adhesive
and let it set for a couple of minutes (see Figure

7-34).

Figure

7-34. Application of Accelerant

Содержание Celeron Dual-Core E1000 Series





















































































































































Результаты поиска

Содержание Celeron Dual-Core E1000 Series

Отзывы:

Похожие инструкции для Celeron Dual-Core E1000 Series

Бренды по названию

Популярные бренды

Intel Celeron Dual-Core E1000 Series, Руководство по дизайну

Результаты поиска

Содержание Celeron Dual-Core E1000 Series

Отзывы:

Похожие инструкции для Celeron Dual-Core E1000 Series

Бренды по названию

Популярные бренды