Intel 81341 Скачать руководство пользователя страница 88 | Manualshive

Страница: 88 / 1056

background image

Intel

®

81341 and 81342—Address Translation Unit (PCI-X)

Intel

®

81341 and 81342 I/O Processors

Developer’s Manual

December 2007

88

Order Number: 315037-002US

2.6

ATU Queue Architecture

ATU operation and performance depends on the queueing mechanism implemented

between the internal bus interface and PCI bus interface. As indicated in

, the

ATU queue architecture consists of separate inbound and outbound queues. The

function of each queue is described in the following sections.

2.6.1

Inbound Queues

The inbound data queues of the ATU support transactions initiated on a PCI bus and

targeted at either 81341 and 81342 local memory or a 81341 and 81342 memory

mapped register.

details the name and sizes of the ATU inbound data queues.

2.6.1.1

Inbound Write Queue Structure

The ATU Inbound Write Queues consist of the inbound write data queue and the

inbound write address queue. The inbound write data queue holds the data for memory

write transactions moving from a PCI Bus to the internal bus and the address queue

holds the corresponding address of the transactions in the data queues. The inbound

write queue, IWQ, has a queue depth of 4 KBytes and moves write transactions from

the PCI bus to the internal bus. The corresponding address queue, IWADQ, is capable

of holding 4 address entries. The queue pair is capable of holding up to 4 memory write

(or MWI when operating in the conventional PCI mode) transactions.
The following rules apply to the PCI bus interface and govern the acceptance of data

into IWQ and address into the tail of the IWADQ:

• A memory write operation claimed by the target PCI interface on the PCI bus is

accepted into the address and data queues when the IWADQ has at least one

address entry available.

• When operating in the conventional PCI mode, when the IWQ reaches a full state

while filling, a disconnect with data is signaled to the master of the transaction.

• When operating in the PCI-X mode, when the IWQ reaches a full state while filling,

a disconnect at next ADB is signaled to the master of that transaction.

Memory write transactions are drained from the head of the queue when the master

interface has acquired bus ownership and transaction ordering and priority have been

satisfied (see

). A memory write transaction is considered drained from

the queue when the entire amount of data entered on the PCI bus has been accepted

by the internal bus target. Error conditions resulting in the cancellation of a write

transaction only flush the transaction at the head of the data and address queue. All

other transactions within the queues are considered still valid.

Table 7.

Inbound Queues

Queue Mnemonic

Queue Name

Queue Size

(Bytes)

IWQ

Inbound Write Data Queue

4 KBytes (4*1KB)

IWADQ

Inbound Write Address Queue

4 Transaction Addresses

IRQ

Inbound Read Data Queue

4 KBytes (4*1KB)

IDWQ

Inbound Delayed Write address/data

Queue

1 Transaction

ITQ

Inbound Transaction Queue

8 Addresses/Commands

«
...
86
87
88
89
90
...
»

Содержание 81341

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 81341

Бренд: ABB Страницы: 66

Бренд: Maco Страницы: 38

Бренд: Quantum Страницы: 20

Бренд: mikroElektronika Страницы: 3

Бренд: Maxim Страницы: 26

Emulator MCU Board for 38D5 Group M38D59T-RLFS

Бренд: Renesas Страницы: 4

Бренд: Z Microsystems Страницы: 51

Compact NVR-AS 4000

Бренд: IndigoVision Страницы: 38

Бренд: Aurora Страницы: 6

Бренд: uneron Страницы: 13

Бренд: RAID Страницы: 80

Бренд: WIN Enterprises Страницы: 25

Бренд: Moxa Technologies Страницы: 8

Бренд: Juniper Страницы: 30

Бренд: Adaptec Страницы: 2

Бренд: silicom Страницы: 16

Бренд: netsys Страницы: 38

iConverter GX/F

Бренд: Omnitron Systems Technology Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды