Integra DTR-30.5, Инструкция по эксплуатации, Страница: 55 / 96

Advanced Operations
En-55
Operating
procedure
(
➔
page 50 )
`
On
`
Off
Turn this setting on to boost bass output by feeding
bass sounds from the front left, right, and center
channels to the subwoofer. Default setting: “
- - - -
”
Note
• When the “ Subwoofer ” setting is set to “ No ” or the “ Front ”
setting to anything other than “ Full Band ”, this setting is
fixed to “ - - - ”.
• This setting is set to “ On ” automatically when the
“ Subwoofer ” and “ Front ” settings are set for the first time
to “ Yes ” and “ Full Band ” respectively.
Speaker Distance
Here you can specify the distance from each speaker
to the listening position so that the sound from each
speaker arrives at the listener’s ears as the sound
designer intended.
■
Unit
`
feet :
Distances can be set in feet. Range: 0.2ft to
30.0ft in 0.2 foot steps.
`
meters :
Distances can be set in meters. Range: 0.06m
to 9.00m in 0.06 meter steps.
(The default setting varies from country to country.)
■
Left, Front High Left, Center, Front High Right,
Right, Surround Right, Surround Back Right,
Surround Back Left, Surround Left, Subwoofer
`
Specify the distance from each speaker to your
listening position.
Note
• Speakers that you set to “ No ” or “ None ” in
“Speaker Configuration” cannot be selected (
➔
page 54 ).
• When the “ Powered Zone 2 ” setting is set to “ Yes ” and
Zone 2 is turned on, the surround back and front high
speakers cannot be used.
Level Calibration
Here you can adjust the level of each speaker with
the built-in test tone so that the volume of each
speaker is the same at the listening position.
■
Left, Front High Left, Center *1 , Front High Right,
Right, Surround Right, Surround Back Right,
Surround Back Left, Surround Left
`
–12dB to 0dB to +12dB in 1 dB steps.
■
Subwoofer
*1
`
–15dB to 0dB to +12dB in 1 dB steps.
Note
• These settings cannot be calibrated when the AV receiver
is muted.
• Speakers that you set to “ No ” or “ None ” in
“Speaker Configuration” cannot be selected (
➔
page 54 ).
• When the “ Powered Zone 2 ” setting is set to “ Yes ” and
Zone 2 is turned on, the surround back and front high
speakers cannot be used.
*1 For the center speaker and subwoofer, the level settings
made by using the Quick Setup are saved in this menu
(
➔
page 49 ).
Tip
• If you’re using a handheld sound level meter, adjust the
level of each speaker so that it reads 75 dB SPL at the
listening position, measured with C-weighting and slow
reading.
With the Audio Adjust functions and settings, you can
adjust the sound and listening modes as you like.
Multiplex/Mono
■
Multiplex
Input Channel
`
Main
`
Sub
`
Main/Sub
This setting determines which channel of a stereo
multiplex source is output. Use it to select audio
channels or languages with multiplex sources,
multilingual TV broadcasts, and so on.
■
Mono
Input Channel
`
Left + Right
`
Left
`
Right
This setting specifies the channel to be used for
playing any 2-channel digital source such as Dolby
Digital, or 2-channel analog/PCM source in the Mono
listening mode.
Dolby
■
PL IIx Music (2ch Input)
These settings apply to only 2-channel stereo
sources.
If you’re not using any surround back speakers, these
settings apply to Dolby Pro Logic II, not Dolby Pro
Logic IIx.
Panorama
`
On
`
Off
This setting is set automatically by
Audyssey MultEQ
® Room Correction and Speaker
Setup function (
➔
page 23 ).
This setting is set automatically by
Audyssey MultEQ Room Correction and Speaker
Setup function (
➔
page 23 ).
3. Audio Adjust