Integra DTR-30.4, Инструкция по эксплуатации

Страница: 60 / 100

Advanced Operations
En-60
■
Picture Mode
*1*7
`
Custom :
All settings can be performed manually.
`
Cinema :
Select when the picture source is a movie or alike.
`
Game :
Select when the video source is a game console.
`
Through :
Does not adjust picture quality (changes resolution).
`
Direct :
Does not adjust picture quality (does not change
resolution). The video coming from an analog input
and output by HDMI output(s) is processed in the
same way as “
Through ”.
With “ Picture Mode ”, you can change the following
settings to be suitable for the movie or game screen by one
operation; “
Game Mode ”, “ Film Mode ”, “ Edge
Enhancement ”, “ Noise Reduction ”, “ Brightness ”,
“ Contrast ”, “ Hue ”, “ Saturation ” or “ Color
Temperature ”.
■
Game Mode
*2*3*4
`
Off
`
On
If video signal delay occurs during playback on a video
component (i.e., game console), select the corresponding
input source and set the “
Game Mode ” setting to “ On ”.
The delay will decrease but in return the picture quality will
become poor.
■
Film Mode
*2*4
`
Video :
“ Film Mode ” detection is not applied and the input
signal is handled as a video source.
`
Auto :
Detects whether the input signal is a video or a
movie. If it is a movie, the appropriate conversion is
applied.
The AV receiver will adjust to the picture source,
automatically converting it to the appropriate progressive
signal and reproducing the natural quality of the original
picture.
■
Edge Enhancement
*2*4*5
`
Off
`
Low
`
Mid
`
High
With this setting, you can make the picture appear sharper.
■
Noise Reduction
*2*4*5
`
Off
`
Low
`
Mid
`
High
With this setting, you can reduce noise appearing on the
screen. Select the desired level.
■
Brightness
*1*2*4
`
–50 to 0 to +50
With this setting, you can adjust the picture brightness.
“
–50 ” is the darkest. “ +50 ” is the brightest.
■
Contrast
*1*2*4
`
–50 to 0 to +50
With this setting, you can adjust contrast. “ –50 ” is the
least. “ +50 ” is the greatest.
■
Hue
*1*2*4
`
–50 to 0 to +50
With this setting, you can adjust the color hue between
“
–50 ” and “ +50 ”.
■
Saturation
*1*2*4
`
–50 to 0 to +50
With this setting, you can adjust saturation. “ –50 ” is the
weakest color. “ +50 ” is the strongest color.
■
Color Temperature
*2*4
`
Warm
`
Normal
`
Cool
With this setting, you can adjust the color temperature.
Note
• “ Picture Adjust ”
cannot be used when:
– The NET input selector is selected, or
– “ Monitor Out ” is set to “ Sub ”.
*1 This procedure can also be performed on the remote controller
by using the Quick Setup (
➔
page 45
).
*2 When the “ Picture Mode ” setting is set to anything other than
“ Custom ”, this setting cannot be used.
*3
If the “ Resolution ” setting is set to “ 4K Upscaling ”
(
➔
page 50 ), this setting is fixed at “ Off ”.
*4 Press CLR if you want to reset to the default value.
*5 If the “ Game Mode ” setting is set to “ On ”, this setting is fixed
at “ Off ”.
*6 When a 3D video source is input, “ Wide Mode ” is fixed to
“ Full ”.
*7
When “ Metadata Compatible ” is enabled, “ Picture Mode ” is
fixed to “ Direct ” (
➔
page 55 ).