•
No power.
Cause:
Power cable is not properly plugged into the AC
outlet.
Remedy:
Insert the power plug firmly.
•
A disc is loaded in the disc tray, but playback will not start.
Cause:
A disc in the disc tray may be upside down.
Remedy:
Load the disc with the label facing upward.
Cause:
The disc is dirty.
Remedy:
Clean the disc.
Cause:
Moisture has accumulated inside the CD changer.
Remedy:
Remove the disc from the disc tray, place the
CD changer in a warm place, and leave the
power on for about one hour.
•
No sound is heard.
Cause:
Connections may be incomplete or incorrect.
Remedy:
Check all cable connections. Insert all the
plugs firmly into the jacks.
Cause:
The input selector switch on the amplifier may be
set incorrectly.
Remedy:
Set the switch to the proper position. See your
amplifier’s operating instructions for more in-
formation.
•
Disc playback skips.
Cause:
The disc is dirty.
Remedy:
Clean the disc.
Cause:
A disc is scratched.
Remedy:
Replace the disc.
Cause:
The CD changer is subject to being accidentally
bumped.
Remedy:
Place the CD changer in a more stable
location.
•
Search time (when locating a specific track) is extremely
long.
Cause:
The disc is dirty.
Remedy:
Clean the disc.
Cause:
The disc is scratched.
Remedy:
Replace the disc.
•
Track numbers cannot be stored in memory.
Cause:
No disc in the tray.
Remedy:
Load a disc in the tray.
Cause:
You have entered a track number that does not exist
on the disc.
Remedy:
Use only the track numbers that exist on the
disc.
•
Front panel controls function correctly, but remote controller
does not.
Cause:
No batteries in remote controller.
Remedy:
Insert batteries.
Cause:
Batteries have worn out.
Remedy:
Replace batteries.
Because the unit contains a microcomputer to provide advanced functions, it
may malfunction due to external noise or static electricity. If this happens, press
the Power button on the unit and then press it in again after about five seconds.
Troubleshooting Guide
Signal readout system:
Optical non-contact
Reading rotation:
About 500 - 200 r.p.m.
(constant linear velocity)
Linear velocity:
1.2 - 1.4 m/s
Error correction system:
Cross Interleave Reed-Solomon code
D/A converter:
1 bit PWM/ACCUPULSE
Sampling frequency:
352.8 kHz (8 times oversampling)
Number of channels:
2 (stereo)
Frequency response:
5 Hz - 20 kHz
Total harmonic distortion:
0.005% (at 1 kHz)
Dynamic range:
96 dB
Signal to noise ratio:
92 dB
Channel separation:
92 dB (at 1 kHz)
Wow and Flutter:
Below threshold of measurability
Output level:
2 volts r.m.s.
Power consumption:
10 watts
Power supply:
120 V, 60 Hz
Dimensions (W
×
H
×
D):
435
×
131
×
433mm
(17-1/8"
×
5-3/16"
×
17-1/16")
Weight:
6.9 kg (15.2 lbs.)
Specifications and features are subject to change without notice.
Specifications
Integra Division of
ONKYO U.S.A. CORPORATION
200 Williams Drive, Ramesy, N.J. 07446, U.S.A.
Tel: 201-825-7950 Fax: 201-825-8150 E-mail: [email protected]
Integra Division of
ONKYO CORPORATION
Sales & Product Planning Div. :
2-1, Nisshin-cho, Neyagawa-shi, OSAKA 572-8540, JAPAN
Tel: 072-831-8111 Fax: 072-833-5222
E
SN 29342934
W0005-1
Integra Division of
ONKYO U.S.A. CORPORATION
200 Williams Drive, Ramesy, N.J. 07446, U.S.A.
Tel: 201-825-7950 Fax: 201-825-8150 E-mail: [email protected]
Integra Division of
ONKYO CORPORATION
Sales & Product Planning Div. :
2-1, Nisshin-cho, Neyagawa-shi, OSAKA 572-8540, JAPAN
Tel: 072-831-8111 Fax: 072-833-5222
CDC-3.1_14-16
09/05/2000, 4:25 PM
16