Inta HIPER II Скачать руководство пользователя страница 21

Страница: 21 / 28

SECTION 7

The HIU Controller first power up and set up

Page 21

SECTION 10

Fault and Error Codes / Fault finding guide

Power on, HIU operating

normally

YES

NO POWER?

Comply with all safety provisions.

Installation and maintenance can only be car-
ried out by a qualified and competent plumb-
ing installer and a qualified and competent
electrical installer in accordance with the cur-
rent document Building Regulations, Legisla-
tion and Standards.

SAFETY

–

before any electrical work or

maintenance ensure that the electrical supply
is isolated.

DANGER

–

immediate risk of physical injury or

even death.

Check that the volt free connections
for room thermostat or Prepayment

have NOT been wired to 230V

Is there power to the

fused spur connecting to

the HIU?

Check power supply and

Fuse feeding to the HIU.

Fused spur requires a

13A Fuse all correct?

Turn off the potential power
supply using the isolation
switch fused spur. Check Fuse
and wiring within the HIU.
6.3 AMP Glass Fuse

If 230 v has been applied to the room
thermostat connections then the

controller maybe damaged beyond
repair and will have to be replaced.
Warranty will not cover this!

YES

Check power is on the HIU electronic
controller. Remove the installer panel
and check Live and Neutral connections.
Are they connected?

YES

Power is at the connections to
the controller, but the controller
screen is blank.

Make good the electrical
connections to the HIU
controller.

Order a HIU new controller

and replace

YES

06/21 E&OE

Содержание HIPER II





























Результаты поиска

Содержание HIPER II

Отзывы:

Похожие инструкции для HIPER II

Бренды по названию

Популярные бренды

Inta HIPER II, Инструкция по установке и эксплуатации

Результаты поиска

Содержание HIPER II

Отзывы:

Похожие инструкции для HIPER II

Бренды по названию

Популярные бренды