InstantEye Mk-3 GEN4-D1 Скачать руководство пользователя страница 35

Страница: 35 / 68

InstantEye Mk-3 GEN4-D1 sUAS Technical Manual

Revision M1.2

August 14, 2019

ITAR or EXPORT CONTROLLED

Page 35

Figure 35. The RECENT SNAP button on the flight screen of the viewing device is shown

with a red arrow.

3.9. Optional Return-to-Base Waypoint Entry

The home location for the aircraft, by default, is the GPS location of the GCS. If the GCS

does not have a GPS location because of a poor GPS signal in its location, then the

aircraft home position becomes the aircraft launch position. If the operator would like the

aircraft to return to an alternate home location, a new Return-to-Base (RTB) location can

be manually entered prior to launching the aircraft. RTB location entry is done by pressing

the

SET RTB

button at the bottom of the main application screen (Figure 36 through

Figure 38).

•

Programming an alternate RTB point will allow the aircraft to go to a designated

waypoint if:

–

HOME

button is pressed

–

Aircraft goes into lost comms mode

–

RTB point is valid

•

Waypoints must be valid for the capability of the aircraft. If not, a warning will

appear, which says “

RTB Upload Fail: Check RTB

” upon attempting to upload the

waypoint to the aircraft.

Содержание Mk-3 GEN4-D1





































































Результаты поиска

Содержание Mk-3 GEN4-D1

Отзывы:

Похожие инструкции для Mk-3 GEN4-D1

Бренды по названию

Популярные бренды

InstantEye Mk-3 GEN4-D1, Руководство по эксплуатации продукта

Результаты поиска

Содержание Mk-3 GEN4-D1

Отзывы:

Похожие инструкции для Mk-3 GEN4-D1

Бренды по названию

Популярные бренды