InstantEye Mk-3 GEN4-D1 Скачать руководство пользователя страница 32

Страница: 32 / 68

InstantEye Mk-3 GEN4-D1 sUAS Technical Manual

Revision M1.2

August 14, 2019

ITAR or EXPORT CONTROLLED

Page 32

using a joystick or by pressing the

NAV

button to disable

NAV

mode. The user should only

enable

HOME

mode when the vehicle is at least 50 feet higher than the surrounding

obstacles. The vehicle is not aware of obstacles and will not avoid obstacles on the way

home that may be in the way. Due to discrepancies between the vehicle GPS and the

GCS GPS, the home location may be in error by as much as 35 meters in poor GPS

conditions and as little as 5 meters in good GPS conditions.

Note:

The

HOME

mode should only be enabled when all systems are operating normally.

It should not be used as an emergency procedure.

3.5.5.4. Landing Mode

Landing mode activates the vertical position controller and commands the aircraft to

slowly descend. Landing mode is automatically initiated when there is a loss of

communication and the aircraft has returned to its home location without regaining

communication with the GCS. This mode can also be entered while in indoor mode. While

in indoor mode, pressing the

HOME

button will initiate the landing mode. Loss of

communications in indoor mode will automatically initiate the landing sequence. Activate

landing mode by pressing and holding the

HOME

button.

3.5.5.5. Lost Communications Mode

Lost communication mode is enabled when the aircraft fails to receive commands from

the GCS. This mode changes depending on the state of indoor mode. While not in indoor

mode, both the translational position controller and the vertical position controller are

activated, allowing the aircraft to climb to a safe altitude and return to the home location.

If the aircraft regains the C2 link in the process of returning home, the operator will once

again have full control. In indoor mode, lost communication mode commands the aircraft

to enter Landing mode. If C2 is regained during the aircraft’s return to HOME, the operator

can wiggle the left joystick to regain control of the aircraft and resume piloting.

3.5.5.6. Camera Aim Point

Camera aim point mode is automatically enabled when the GCS is powered up. While

any selected camera is looking downward, a cursor appears at the center of the field of

view. While this cursor appears on the screen, the GPS location will be calculated at this

point on the ground. In this mode, the location graphic at the bottom of the tablet display

contains the coordinates of the center of the displayed video feed. A small reticle is

generated at the center of the display to aid in pinpointing targets. The indicator has no

information about the ground topography and ASSUMES FLAT GROUND in its

calculation of latitude and longitude. The error in the indicated coordinates will grow with

aircraft altitude and uneven terrain of the underlying ground. Potential error is as great as

twice the size of the indicating reticle box over flat ground and worse over uneven terrain.

When the error is too high, such as when viewing the forward camera feed, the location

graphic will revert to indicating the aircraft location over ground. This is indicated by the

abbreviation “A/C” to the left of the location graphic and the disappearance of the reticle.

3.5.5.7. Rescue

Rescue mode is utilized if the GCS-D is unintentionally powered off midflight by pressing

the

POWER

button, disconnecting the battery, or depleting the battery. Rescue mode

Содержание Mk-3 GEN4-D1





































































Результаты поиска

Содержание Mk-3 GEN4-D1

Отзывы:

Похожие инструкции для Mk-3 GEN4-D1

Бренды по названию

Популярные бренды

InstantEye Mk-3 GEN4-D1, Руководство по эксплуатации продукта

Результаты поиска

Содержание Mk-3 GEN4-D1

Отзывы:

Похожие инструкции для Mk-3 GEN4-D1

Бренды по названию

Популярные бренды