background image

7

PROPERTY DAMAGE

   These plumbing instructions were written for an 

experienced competent installer. If the installer  

is not experienced in plumbing installation,  

InSinkErator recommends that competent  

professional assistance is sought. Damage to  

the disposer or accessories as a result of  

improper installation is not covered under  

warranty. All installations must comply with local 

plumbing codes.

Plumbing Connections

DRAIN LINE CONNECTIONS

To allow easy access to overload reset button, the  
disposer plumbing should be connected with the  
electrical control box facing the operator.

When connecting the drain line, place the "P-trap" as 
close to the disposer outlet flange as possible. Do not 
connect the drain line to a grease trap, interceptor, or 
drum trap.

All horizontal runs should be as short as possible, with a 
minimum fall of 1/4 inch per foot.

WATER SUPPLY CONNECTIONS

When connecting the disposer to the incoming water 
supply, use as few elbows and tees as possible.  
Connect to the cold water line only. All water line  
fittings are 1/2" NPT except the sink bowl nozzles  
(1/2" compression).

Install the flow control valve, water solenoid valve, and 
the syphon breaker according to the direction of the 
flow arrows marked on each valve body (see Figure 9).

NOTE: A syphon breaker must be installed above the 
sink flood plane per local plumbing codes.

ROUTING WATER FLOW

•  In a trough system, route all water flow to the end of 

  the trough to flush food waste.
•  In a sink bowl system route all water through the  

sink bowl.

•  Table 2 provides Recommended Cold Water Flow and 

Drain Line Diameter.

Disposer

Standard

Flow Control

GPM (LPM)

Optional

Flow Control

GPM (LPM)

Drain 

Line

Diameter

SS-50

3 (11)

NA

1-1/2"

SS-75

3 (11)

NA

1-1/2"

SS-100

5 (19)

3 (11)

1-1/2"

SS-125

5 (19)

3 (11)

2" NPT

SS-150

7 (26)

5 (19)

2" NPT

SS-200

7 (26)

5 (19)

2" NPT

SS-300

8 (30)

7 (26)

3" NPT

SS-500

8 (30)

7 (26)

3" NPT

SS-750

10 (38)

NA

3" NPT

SS-1000

10 (38)

NA

3" NPT

Table 2. Recommended Cold Water Flow  

             and Drain Line Diameter

Figure 9. Installation Diagram

Содержание Model SS-200












Отзывы: