background image

11

ELECTRICAL SHOCK

Disconnect power before servicing.

Troubleshooting

Troubleshooting for problems other than what is listed below should be performed by a qualified service person. 
Troubleshooting performed by untrained personnel could result in electrical shock or damage to the disposer.  
Disconnect power before servicing.

PROBLEM

POSSIBLE CAUSE

SOLUTION

Disposer will not start and 
water does not flow.

 • No incoming water. 

 • Electrical disconnect switch  

has been reactivated and  
30-second delay has not  
yet expired.

 • Turn on electrical supply. 

 • Wait 30 seconds and try starting again.

Disposer will not start but 
water flows.

 • Disposer overload protector  

is tripped. 

 • Disposer is jammed.

 • Turn control to off position and press red reset button on 

disposer. 

 • Turn control to off position and complete  

following steps:

 1.  Insert dejamming wrench (not supplied) slot down  

 through sink opening. Place slot over raised bars  
 found on top of rotating shredder.

 2.  Twist dejamming wrench back and forth to free jam.  

 Rotating shredder should revolve freely when jam  
 is released.

 3.  Remove all foreign materials.
 4.  Allow disposer to cool for 3-5 minutes after it stops  

 running. Press red reset button to reset overload  
 protector. Never strike reset button with objects.

 5.  If disposer remains inoperative after following these 

 steps, contact nearest InSinkErator Factory  
 Authorized Service Center (call 1-800-845-8345  
 to find Service Center nearest you).

Disposer motor stops while 
grinding, but water continues 
to flow.

 • Disposer is jammed. 

 • Disposer overload protector  

is tripped.

 • See "Disposer is jammed," above. 

 • Turn control to off position and press red reset button on 

disposer. If disposer was running, allow unit to cool 3-5 
minutes before pressing red reset button. Never strike 
reset button with objects.

Water flows continuously  
before controls are turned on.

 • Reinstall water solenoid valve with arrow on valve 

pointing in direction of the water flow.

Overload protector  
trips frequently.

 •  Disposer is overloaded with 

food waste.

 •  Do not overload disposer with excessive amounts of 

food waste.

Содержание Model SS-200












Отзывы: