Inside Out Networks Digi Edgeport/1i Скачать руководство пользователя страница 9 | Manualshive

Страница: 9 / 22

Inside Out Networks Digi Edgeport/1i Скачать руководство пользователя страница 9

Edgeport Industrial Installation Guide (90000409 Rev. C) – Page 7

Configuring the Port Flags

The Edgeport/4s MEI and Edgeport/8s MEI, which support RS-232, RS-422 and RS-485, are
configured using the Edgeport Utility program. Before configuring, make sure that the drivers
have been installed and that the device is connected to your computer.

Open edgeport.exe, select the Edgeport that you want to configure, and click on the Port Flag
Configuration button. The drop down boxes under the Industrial Settings allows you to select from
the following options for each port listed:

RS232
RS422: No Terminating Resistor
RS422: Terminating Resistor
RS485: Half Duplex, End Unit, Echo
RS485: Half Duplex, End Unit, No Echo
RS485: Half Duplex, Middle Unit, Echo
RS485: Half Duplex, Middle Unit, No Echo
RS485: Full Duplex, End Unit, Master
RS485: Full Duplex, End Unit, Slave
RS485: Full Duplex, Middle Unit, Master
RS485: Full Duplex, Middle Unit, Slave

If the drivers are not already installed, go to "Edgeport Driver Installation” starting on page 8.

«
...
7
8
9
10
11
...
»

Содержание Digi Edgeport/1i























Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды