Inscape Data Link Power LPS3800-T1 Series Скачать руководство пользователя страница 3

Page | 3 
 

Safety Summary 

The following general safety precautions must be observed during all phases of operation of this 
instrument. Failure to comply with these precautions or with specific warnings elsewhere in this 
manual violates safety standards of design, manufacture, and intended use of the instrument. 
Inscape Data Corporation assumes no liability for the customer’s failure to 
comply with these requirements.  
 

Before Applying Power 

Verify that the product is set to match the available line voltage and all safety precautions are 
taken. 
 

Over Temperature Warning 

To prevent the switch from overheating, do not operate it in an area that exceeds the maximum 
recommended ambient temperature of (75°C). To prevent product cooling restriction, allow at 
least 3 inches (7.6 cm) of clearance around the product after installation. 
 

Ground the Instrument 

To minimize shock hazard, the instrument chassis and cabinet must be connected to an 
electrical ground. The instrument must be connected to the ac power supply mains through a 
three-conductor power cable, with the third wire firmly connected to an electrical ground (safety 
ground) at the power outlet. For instruments designed to be hard-wired to the ac power lines 
(supply mains), connect the protective earth terminal to a protective conductor before any other 
connection is made. Any interruption of the protective (grounding) conductor or disconnection of 
the protective earth terminal will cause a potential shock hazard that could result in personal 
injury.  
 
When installing the unit, always make the ground connection first and disconnect it last. 

 

Jewelry Removal Warning 

Before working on equipment that is connected to power lines, remove jewelry (including rings, 
necklaces, and watches). Metal objects will heat up when connected to power and ground and 
can cause serious burns or weld the metal object to the terminals. 

 

Do not Operate in Explosive Atmosphere 

Do not operate the product in the presence of flammable gases or fumes. 
 

 

Содержание Link Power LPS3800-T1 Series
















Отзывы: