INR LINC 21, Руководство по установке, Страница: 6 / 12

6 ((12))
Filter change and cleaning 150 cc SHOWER MIXER
• Shut down water supply to mixer.
• Remove the mixer by loosening the nuts (13) from the mixing rail or wall box.
• The filters (14) can remain in the nuts (13) or on rail or mixes. wall box. Remove them carefully.
• Wash filters (14) under running water or leave to soak in vinegar or de-scaling agent.
• Refit the filters the above procedure in the reverse order.
• See paragraph “Plumbing and installation” for refitting.
Filter change and cleaning 160 cc SHOWER MIXER
• Shut down water supply to mixer.
• Unscrew the nuts of the fixing plate from the seats (13) and remove the mixer from the wall.
• Carefully remove the circlip (16) and take out the filter (15).
• Wash filters (15) under running water or leave to soak in vinegar or de-scaling agent.
• Refit the filters following the above procedure in the reverse order.
• See paragraph “Plumbing and installation” for refitting.
Cartridge change and cleaning
• Shut down water supply to the mixer.
• Prise-off the cap (1) and undo grub screw (2) in order to remove the temperature handle (3).
• Remove the stop ring (4).
• Unscrew and remove the cartridge (5) from the mixer being careful not to damage the seals. Wash the thermostat
under running water or leave to soak in vinegar or de-scaling agent.
• Before refitting the cartridge clean the mixer housing and grease the valve o-rings.
• Place the cartridge into the mixer and tighten it at 15 Nm.
• Turn the water supply back on. Measure water temperature with a thermometer. Set the mixed flow temperature at
38°C. See paragraph “Cartridge re-settning”.
• Re-fit the stop ring (4) in its original position.
• Re-fit the temperature handle (3) so that the pin inside the handle is next to the stopper on the upper part of the stop
ring (4). Make sure that the 38°C etching on the lever is aligned with the HOT etching on the body.
Cartridge re-setting
The mixer is factory set at 38°C. This can however be adjusted for site conditions or personal preference. In order to do this,
proceed as follows:
•
Use a common household thermometer to test water temperature.
• Remove the temperature handle (3) by prising off indice (1) and undoing grub screw (2).
• Remove the stop ring (4) taking note of its position.
• Turn the spindle of the cartridge (5) clockwise or anticlockwise until the desired temperature is reached, paying
attention not to damage the broached part.
• Re-fit the stop ring (4) in its original position.
• Place the temperature handle so that the pin inside the handle is next to the stopper on the upper part of the stop
ring (4), making sure that the lever is pointing downwards and the 38°C etching on the lever is aligned with the HOT
etching on the body. Fix it with the grub screw (2) and then place the cap (1).
Diverter change
• Shut down water supply to the mixer.
• Unscrew lever (12) and undo grub screw (10) in order to remove the flow handle (9).
• Unscrew the stop ring (7) and remove the diverter (6) from the mixer being careful not to damage the seals.
• Place the new diverter into the mixer making sure to use the broached insert (8) and tighten the stop ring (7) at 8 Nm
and re-assemble the handle following the above procedure in the reverse order.
• Turn the water supply back on and check for leaks.
Cleaning
Chromed surfaces should be cleaned using a soft cloth and a mild soap solution. The surface should then be flushed with
clean water and dried using a soft dry cloth. Use household vinegar for removing lime scale from chromed surfaces.
Clean shower rose rubber parts regularly by “massaging” them with your hand.
For more information visit our website at www.inr.se