Inovonics JUSTIN 808 Скачать руководство пользователя страница 8

Страница: 8 / 49

— 6 —

JUSTIN 808 TECHNICAL SPECIFICATIONS

OFF-AIR RECEIVER

Antenna Input:

75-ohm (‘F’ connector)

Receiver Tuning Range:

87.5MHz–108.0MHz in 100kHz steps

Receiver Sensitivity:

The internal FM/HD Radio receiver re-

quires approximately 20dBµV (10µV) to

recover analog and digital programs with

adequate SNR for autocorrelation.

SIGNAL PATH

Digital Audio I/O:

The AES3 (XLR) 24-bit stereo audio pass-

through operates at a fixed 44.1kHz sam-

pling rate.

Available Audio Delay:

16 seconds

Available Audio Level Correction:

±6dB

NETWORKING

An RJ45 jack accepts TCP/IP network connec-

tions for remote setup and operation of

the JUSTIN 808.

FAILOVER AUDIO PROTECTION

Relay contacts bypass the AES digital au-

dio pass-through in event of AC mains

power loss.

THE USER INTERFACE

Front-Panel Interface:

A front-panel graphic display and jog

wheel allow easy, menu-guided

in-situ

set-

up and operation of the JUSTIN 808.

Level Metering:

LED “VU” meters display FM, HD1 and AES

loop-through program audio levels.

Delay Metering:

A segmented LED display shows FM–HD1

alignment ,

5 and 5 samples.

Software Control:

The IP network port enables complete

remote setup and operation of the JUSTIN

808 over a local network or the Internet

using any desktop, tablet or mobile

browser.

SNMP:

SNMP remote monitoring and control is

supported.

MISCELLANEOUS

Headphone Jack:

A front-panel, quarter-inch (TRS) head-

phone jack allows the user to monitor ei-

ther the AES digital audio passing through

the JUSTIN 808, or the off-air signal in

‘split mode,’ with the analog FM signal in

the left channel and the HD Radio signal

in the right channel. Headphone volume

is a menu item.

AC Mains Requirements:

90–130VAC or 200–255VAC, 50/60Hz; 7W

‘Boot’ Time:

3 seconds to full operation

Size:

W: 19in/483mm, H: 1¾in/44mm,

D: 9½in/240mm (1U).

Weight:

9lb/4kg (net), 12lbs/5.4kg (shipping)

Environmental:

Continuous operation guaranteed at ambi-

ent temperatures between 32°F/0°C and

122°F/50°C; 0-95% relative humidity, non-

condensing; altitudes to 10,000ft/ 3048m.

Conformances:

EN50081-1

EN50082-1

93/68/EEC

2002/95/EC

Содержание JUSTIN 808


















































Результаты поиска

Содержание JUSTIN 808

Отзывы:

Похожие инструкции для JUSTIN 808

Бренды по названию

Популярные бренды

Inovonics JUSTIN 808, Инструкция по установке и эксплуатации

Результаты поиска

Содержание JUSTIN 808

Отзывы:

Похожие инструкции для JUSTIN 808

Бренды по названию

Популярные бренды