manualshive.com logo in svg

Inovonics 708, Инструкция по эксплуатации и техническому обслуживанию

Поделиться
Скачать
Inovonics 708 Скачать руководство пользователя страница 33

 

—      — 

31

comprise the Model 708 display.  The front-panel meter is scaled both 

in percent-modulation and in dB.  This is similar to a standard VU 

meter except for the peak-response ballistics. 
Each of the three LED bargraph modules is 

series

-connected.  This is a 

power-saving technique since each 

module

,

 

rather than each individual 

segment

, draws only 5 milliamps.   This technique does demand more 

than the bipolar 9-volt regulated supply, however, so the LEDs and 

their associated driver ICs use a separate ±12-volt supply taken prior 

to the 9-volt regulators. 

POWER SUPPLY 

Stereo Generator circuitry operates from a bipolar 9-volt supply.  The 

two supplies are regulated by linear “three-terminal” IC voltage 

regulators: IC2 for the +9-volt supply, IC3 for the –9-volt supply.  The 

power transformer has dual primary windings which may be switched in 

parallel or in series for 115V or 230V mains, respectively. 
The rectified raw DC from the input filter capacitors runs the front-

panel LED bargraph display.  Emitter-followers Q1 and Q2, clamped by 

zener diode CR10, prevent the LED supply from exceeding a total of 24 

volts, overall. 

Содержание 708








































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды