Inovonics 708 Скачать руководство пользователя страница 25

Страница: 25 / 39

— —

Input Level

Calibration

NOTE:

This portion of 708 calibration must follow the preceding

Crosstalk Trim procedure directly.
1. Re-apply 400Hz to both channels and monitor the filter buffer stage

at R128 and R135, just as described at the beginning of this

Procedure.

2. Turn the

O’SHOOT COMP

. switch to the

position.

3. Make no changes to the 708

INPUT GAIN

controls. Note that as the

output level of the Audio Generator is increased, the 9-volt p-p

waveforms will clip, or flatten, top and bottom. Carefully, adjust

the output level of the Audio Generator to a point where the

flattening is scarcely visible. As the

O’SHOOT COMP.

switch is

switched between

and

OUT

, there should be a just-perceptible

change in the amplitude of the waveform(s) as the clipping circuit is

biased into, and out of, operation. This Audio Generator output

level setting represents the 100%-modulation level as applied to the

708

PROGRAM LINE INPUT

terminals.

4. With the front-panel meter monitoring the left-channel input,

adjust R45 for a

half-brightness

indication of the

0dB

, LED.

5. Step the meter to monitor the right-channel input,

, and adjust

R46 for a half-brightness indication of the

0dB

LED.

6. Verify that

L+R

metering indicates

0dB

with the LED at full

brightness, and that nothing shows in the

L–R

position.

Output Level

Calibration

NOTE

: This portion of 708 calibration must follow the preceding

Input Level Calibration procedure directly.
1. Set the

MODE

switch to

STEREO

and turn the

PILOT

switch

2. With the 400Hz, 100%-modulation input signals applied, turn the

front-panel

COMPOSITE PROCESSING

control fully clockwise to

the

+3dB

marking.

3. With the Modulation Monitor connected to the

COMPOSITE

OUTPUT

of the 708, and with the Mod-Monitor set to read Total

Modulation in its peak-responding mode, adjust the

OUTPUT LEVEL

control of the 708 for a 100% Mod-Monitor reading.

4. Switch the Mod-Monitor to measure the 19kHz stereo pilot

injection level, and adjust the 708 front-panel

PILOT INJ.

control for

a 10% reading.

5. If necessary, repeat Steps 3 and 4 to secure simultaneous 100%

Total Mod. and 10% Pilot readings.

6. With 708 front-panel metering switched to

MPX

, adjust R47 for a

0dB

indication.

7. With 708 metering switched to

PILOT

, adjust R48 for a

0dB

indication.

Содержание 708








































Результаты поиска

Содержание 708

Отзывы:

Бренды по названию

Популярные бренды

Inovonics 708, Инструкция по эксплуатации и техническому обслуживанию

Результаты поиска

Содержание 708

Отзывы:

Бренды по названию

Популярные бренды