Inovonics 235 Скачать руководство пользователя страница 35

Страница: 35 / 35

INOVONICS WARRANTY

TERMS OF SALE:

Inovonics products are sold with an understanding

of “full satisfaction”; that is, full credit or refund will be issued for

products sold as new if returned to the point of purchase within 30 days

following their receipt, provided that they are returned complete and in

an “as shipped” condition.

CONDITIONS OF WARRANTY:

The following terms apply unless

amended

in writing

by Inovonics, Inc.

A. Warranty Registration Card supplied with product

must

completed and returned to Inovonics within 10 days of delivery.

B. Warranty applies only to products sold “as new.” It is extended only

to the original end-user and may not be transferred or assigned

without prior written approval by Inovonics.

C. Warranty does not apply to damage caused by misuse, abuse,

accident or neglect. Warranty is voided by unauthorized attempts at

repair or modification, or if the serial identification has been

removed or altered.

III

TERMS OF WARRANTY:

Inovonics, Inc. products are warranted to be

free from defects in materials and workmanship.
A. Any discrepancies noted within 90 days of the date of delivery will

be repaired free of charge, or the equipment will be replaced with a

new or remanufactured product at Inovonics’ option.

B. Additionally, parts for repairs required between 90 days and one

year from the date of delivery will be supplied free of charge. Labor

for factory installation of such parts will be billed at the prevailing

“shop labor rate.”

RETURNING GOODS FOR FACTORY REPAIR:

A. Equipment will not be accepted for Warranty or other repair without

a Return Authorization (RA) number issued by Inovonics prior to its

return. An RA number may be obtained by calling the factory. The

number should be prominently marked on the outside of the

shipping carton.

B. Equipment must be shipped prepaid to Inovonics. Shipping

charges will be reimbursed for valid Warranty claims. Damage

sustained as a result of improper packing for return to the factory is

not covered under terms of the Warranty and may occasion

additional charges.

Содержание 235




































Результаты поиска

Содержание 235

Отзывы:

Похожие инструкции для 235

Бренды по названию

Популярные бренды

Inovonics 235, Инструкция по эксплуатации и техническому обслуживанию

Результаты поиска

Содержание 235

Отзывы:

Похожие инструкции для 235

Бренды по названию

Популярные бренды