Inovonics 235 Скачать руководство пользователя страница 28

Страница: 28 / 35

— —

PARTS LIST

EXPLANATION OF PARTS LISTINGS

This section contains listings of component parts used in the Inovonics

235 AM Broadcast Audio Processor. These are listed either

en-masse,

or by schematic component reference designation. The listing may, or

may not, specify a particular manufacturer. When no manufacturer is

called-out, the term “open mfgr.” advises that any manufacturer’s

product is acceptable, so long as it carries the proper generic part

number.
If a particular component is not listed at all, this means that we do not

consider it a typical replacement item. Should you need to order an

unlisted part, call, write or FAX the factory with a brief description.

We’ll do our best to figure out what you need and get it on its way to

you quickly.

PARTS LISTING

Unless specifically noted by component reference designation below,

capacitors

are specified as follows:

100pF to 0.47µF

are of the metalized mylar or polyester variety.

Whole number “P” values are picofarads, decimal values are

microfarads, ±5%, 50VDC or better. The style used in the 540 is the

“minibox” package with a lead spacing of 0.2 inch.

Preferred part:

Wima MKS-2 or FKC-2 series.

Alternates:

CSF-Thompson IRD

series, or Roederstein KT-1808 or KT-1817 series.

1.0µF and above

are radial-lead electrolytics, value per schematic,

25VDC; (open mfgr.).

C1,2

Capacitor, Ceramic Disc “Safety” Mains Bypass, .0047µF, 440VAC;

Murata/Erie DE7150 F 472M VA1-KC (preferred)

C4,5

Capacitor, Electrolytic, axial leads, 1000µF, 35VDC; (open mfgr.)

C15

Capacitor, Memory Back-Up, 1 Farad, 5.5VDC; (open mfgr.)

C21-24,

26,29-33

Capacitor, “High-Q,” .0033µF, 2.5%, 100VDC; Wima FKC-2

(Polycarbonate) preferred, any equivalent

must

have

similar, very-low-loss characteristics.

C38,39

Capacitor, Electrolytic, radial leads, 220µF, 6VDC; (open mfgr.)

CR1,2,11-29

Diode, Silicon Signal; (open mfgr.) 1N4151 or equiv.

CR3-10

Diode, Silicon Rectifier; (open mfgr.) 1N4005

CRES1

Ceramic Resonator, 4MHz; Mouser 520-ZTT400MG

Содержание 235




































Результаты поиска

Содержание 235

Отзывы:

Похожие инструкции для 235

Бренды по названию

Популярные бренды

Inovonics 235, Инструкция по эксплуатации и техническому обслуживанию

Результаты поиска

Содержание 235

Отзывы:

Похожие инструкции для 235

Бренды по названию

Популярные бренды