Innovative Energies No-Break SR250i 485 Series Скачать руководство пользователя страница 11 | Manualshive

Страница: 11 / 16

Innovative Energies No-Break SR250i 485 Series Скачать руководство пользователя страница 11

Specifications are subject to change without notice. No liability accepted for errors or omissions.

11

Protocol Converter and Software

Installation Instructions

The +PROTOCONMB protocol converter is supplied with programming software and two interconnecting cables. The
converter provides a MODBUS output using a RS485 link as well as a RS232 programming output. Information on
the power supply parameters and control of the battery condition test function are available using these outputs.

PROCEDURE

Install Software from disk Power MBLink v1.3 by clicking on

Setup.exe

Click Start / ‘All Programs / DoZeener Controls / Innovative Energies Power MBLink
v1.2’

The program will begin - “Configuration” tab will show:

In Communication settings

: Click on ‘List Available Ports’ - available ports will be

listed at the bottom of the screen in the “Description” field

Global Solutions Personal Focus

«
...
9
10
11
12
13
...
»

Содержание No-Break SR250i 485 Series

















Отзывы:

Нет отзывов