innovair BIN1036C2V02 Скачать руководство пользователя страница 33 | Manualshive

Страница: 33 / 47

background image

31

8.4.4 Auto-mode

This mode can be chosen with remote controller and the setting temperature can be changed between

17~30

℃

.

In auto mode, the machine will choose cooling or fan-

only mode according to ΔT (ΔT =T1-Ts).

ΔT=T1-Ts

Running mode

ΔT

＞

1

℃

Cooling

-

1<ΔT≤1

℃

Fan-only

Indoor fan will run at auto fan of the relevant mode.

The louver operates same as in relevant mode.

If the setting temperature is modified, the machine will choose running function again.

8.4.6 Forced operation function

8.4.6.1 Forced cooling and auto function can carry out with a touch button. In these two modes, the

machine can be changed by remote controller to any other mode at any moment.

8.4.6.2 When the machine is off, pressing the touch button will carry the machine to forced auto mode,

after this, if pressing the button once again within 5 seconds, the machine will turn into forced cooling

mode. In forced auto, forced cooling or any other operation mode, pressing touch button will turn off

the machine. In forced operation, remote control is available.

8.4.6.3 In forced operation mode, all general protections is available.

8.4.6.4 The compressor runs at F2 frequency and indoor fan runs as breeze. After running for 30

minutes the machine will turn to auto mode as 24

℃

setting temperature.

8.4.6.5 The action of forced auto mode is the same as normal auto mode which temperature is 24

℃

.

8.4.7 Timer function

8.4.7.1 Timing range is 24 hours, and the minimum resolution is 15 minute s.

8.4.7.2 Timer on. After turning off, the machine will turn on automatically when reaching the setting

time.

8.4.7.3 Timer off. After turning on, the machine will turn off automatically when reaching the setting

time.

«
...
31
32
33
34
35
...
»

Содержание BIN1036C2V02
















































Отзывы:

Нет отзывов

Похожие инструкции для BIN1036C2V02

MULTI-TEC W18AAPA

Бренд: Bard Страницы: 51

Бренд: Magic-Pak Страницы: 5

Бренд: ARCTIC WIND Страницы: 17

Бренд: Dimplex Страницы: 11

Бренд: TATA Motors Страницы: 32

Бренд: EarthLinked Страницы: 11

Бренд: Airwell Страницы: 71

ArticCircle AFD4242 C110A

Бренд: AdobeAir Страницы: 4

Бренд: Sonnenkonig Страницы: 36

Бренд: ACPro Страницы: 41

Бренд: Friedrich Страницы: 20

Бренд: Envicool Страницы: 31

Бренд: Dimplex Страницы: 12

Бренд: IQAir Страницы: 12

ARC15AAC Series

Бренд: GE Страницы: 54

ARC13AAC Series

Бренд: GE Страницы: 54

Бренд: Hitachi Страницы: 24

Бренд: Blueair Страницы: 36

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды