manualshive.com logo in svg

Innova Ephoca HPAC 2.0, Руководство по установке

Поделиться
Скачать
Innova Ephoca HPAC 2.0 Скачать руководство пользователя страница 36

36

PROBLEMS AND SOLUTIONS

In the event of a malfunction, refer to the following table. If, after performing the suggested checks, the problem is not 

solved, call the Customer Support Call Center at for assistance.

PROBLEM

POSSIBLE CAUSES

SOLUTION(S)

THE HPAC 2.0 

DOESN’T TURN ON

No power

Check that there is power to the grounded three-prong 
electrical power outlet that is powering the HPAC 2.0 
by plugging in a lamp to the same outlet. Repair the 
grounded three-prong electrical power outlet or use a 
different one.

The fuse is blown/circuit 
breaker is tripped

You may notice a few minutes’ delay in starting if 
you try to restart the HPAC 2.0 too soon after turning 
it off, or if you adjust the thermostat right after the 
compressor has shut off. This is due to a built-in restart 
protector for the compressor that causes a three-minute 
delay.

The HPAC 2.0 is unplugged

During the defrost cycle, both the indoor and outdoor 
fans stop and the compressor will operate in the 
cooling mode to remove frost from the outdoor coil. 
After defrosting, the HPAC 2.0 will restart in electric heat 
to quickly warm the room to the desired comfort level.

The HPAC 2.0 is waiting for 
the compressor overload 
protector to reset

To protect the compressor and prevent short cycling, 
the HPAC 2.0 is designed to run for a minimum of three 
minutes after the compressor starts at any thermostat 
setting.

The current interrupter 
device is tripped

Press the RESET button located on the power supply 
cord plug or the box near the power plug.

If the RESET button will not stay engaged, discontinue 
use of the HPAC 2.0 and contact a qualified service 
technician.

Содержание Ephoca HPAC 2.0









































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды