Innova Ephoca HPAC 2.0 Скачать руководство пользователя страница 24 | Manualshive

Страница: 24 / 40

Innova Ephoca HPAC 2.0 Скачать руководство пользователя страница 24

24

HIGH WALL CONFIGURATION

HPAC 2.0 can be installed close to the floor or near the ceiling (high wall). The unit is factory configured for floor and high

wall installation, where the air flow is directed upwards. This works well for heating and cooling in floor installations and

cooling only in high wall installations (coanda effect).

If installing as a high wall and using for heating as well as cooling, the direction of the air flow must be modified by

adjusting the position of the air louver, so that air blows downwards instead of upwards.

Modification from lower wall to the upper wall installation if

using for heating and cooling.

STEP 1

Disconnect the power

STEP 2

Remove the upper grill

STEP 3

Remove the front cover panel by unscrewing the two

screws in the upper part

STEP 4

Position the bottom cover and install it with the

screws supplied. When mounting the unit on the

upper part of the wall, order the optional bottom

cover decorative kit code GB0737.

WARNING

ELECTRICAL SHOCK HAZARD

Turn off all electrical power before opening the unit. Failure to

disconnect may result in property damage, injury or death.

2

5

3

4

«
...
22
23
24
25
26
...
»

Содержание Ephoca HPAC 2.0









































Отзывы:

Нет отзывов