INIS Oirr MK2 Скачать руководство пользователя страница 9

Страница: 9 / 15

Inis Oirr MK2 Multifuel Boiler stove

Installation Manual

Specification

Output Kw
Water Kw

8.5

Flue Dia mm

153

Flue Gas
Temperature

266

Fuel

Wood, eco
fuels, peat
dried,
smokeless
coal

Min distance to
combustibles

Rear mm
Sides mm

150
250

CO @ 13%O2 %

0.14

Stove Mass
KG

165

Max Hearth Temp

Installation Instructions

The heat outputs as shown above were

obtained using well-seasoned hardwood

using a refuelling time of 1.5 hrs.

The wooden crating the stove was shipped

in can be cut up for fuel in the stove.

Health and Safety

precautions

Please ensure that the installation of

the stove complies with all the

requirements of the relevant Health and

safety at work acts applicable.

Some materials used in fire cement are

caustic and contact with the skin should

be avoided. In case of contact with the

skin wash with plenty of cold water.

If any structural work is required for

installation please take note of the

possible presence of asbestos. If the

presence of asbestos is found please

contact a registered asbestos removal

firm.

Combustion and

ventilation air

requirements

Proper air supply must be insured to the

room into which the stove is to be

installed. A permanent vent opening with

a minimum free area of 65 cm sq. must be

present and ensure that the vent cannot

be blocked for example by fallen leaves

and that any grills that fit the vent do

not lessen the cross section of the

vent. Under no circumstances should

there be an extractor fan in the same

room as the stove, to avoid the

possibility of combustion gases being

drawn into the room.

Содержание Oirr MK2
















Результаты поиска

Содержание Oirr MK2

Отзывы:

Похожие инструкции для Oirr MK2

Бренды по названию

Популярные бренды

INIS Oirr MK2, Руководство пользователя и инструкция по установке

Результаты поиска

Содержание Oirr MK2

Отзывы:

Похожие инструкции для Oirr MK2

Бренды по названию

Популярные бренды