Ingersoll-Rand TRANE NEXIA TZEMT500BB32MAA Скачать руководство пользователя страница 9 | Manualshive

Страница: 9 / 28

Ingersoll-Rand TRANE NEXIA TZEMT500BB32MAA Скачать руководство пользователя страница 9

9

9

If necessary, cut the internal jumper wire (JP1).

24RC
24RH

W1

24RC
24RH

W1

OR

24RC
24RH

W1

Do NOT cut JP1 jumper

Cut JP1 jumper

If only one wire is connected

to either 24RC or 24RH

as shown

If wires are connected to

both 24RC and 24RH

as shown

Cutting the JP1 jumper

The jumper is located on back of the thermostat face as shown in the illustration to
the right. Cut the jumper using small diagonal cutters being careful not to damage
the board.

11

Turn power to heating and cooling system back on.

The thermostat display should turn on and begin displaying information. If the thermostat display does not come on, go back through the
installation steps and look for problems.

10

Attach the thermostat face to the wall plate.

a. Carefully align the face plate to the wall plate while aligning pins into wire terminals.
b. Once thermostat face is properly aligned, apply pressure at top and bottom of thermostat face

until it is secure.

24RC
G

Y1

Y2
RS

2

RS

2

24C

24RH

W1

W2/O

RS

1

RS

2

Shld

HC

Shld

H1

CUT JU

MPE

R T

O

SPLIT

RC/R

H

HC

SHLD

R

S1

24C

24R

H

W1

W2/O

RS

1

H

1

SHLD

R

S2

24R

C

G

Y1

Y2

RS

2

JP1

JP

1

JP

1

CUT JUMPER

TO

SPLIT R

C/RH

SPLIT RC/R

H

CUT JUMPER

TO

«
...
7
8
9
10
11
...
»

Содержание TRANE NEXIA TZEMT500BB32MAA





























Отзывы:

Нет отзывов