E
2010
CCN 15207657
(800) 276-4658
D
FAX (800) 266-7016
INGERSOLL RAND COMPANY LTD
209 NORTH MAIN STREET
-
BRYAN, OHIO 43506
1” DIAPHRAGM PUMP
OPERATOR’S MANUAL
PD10X-X-X
RELEASED:
3-11-04
REVISED:
5-19-10
(REV. 07)
INCLUDING: OPERATION, INSTALLATION & MAINTENANCE
1:1 RATIO (METALLIC)
READ THIS MANUAL CAREFULLY BEFORE INSTALLING,
OPERATING OR SERVICING THIS EQUIPMENT.
It is the responsibility of the employer to place this information in the hands of the operator. Keep for future reference.
PE10X-X-X
SERVICE KITS
Refer to Model Description Chart to match the pump material options.
637397 for air section repair (see page 6).
637401-XX for fluid section repair (see page 4). NOTE: This kit also con-
tains several air motor seals which will need to be replaced.
637395-X major air valve assembly (see page 7).
PUMP DATA
Models
see Model Description Chart for “-XXX”
. . . . . . . . . . . . .
Pump Type
Metallic Air Operated Double Diaphragm
. . . . . . . . . .
Material
see Model Description Chart
. . . . . . . . . . . . .
Weight
PX10R-XAX-XXX
20.65 lbs (9.37 kgs)
. . .
. . . . . . .
PX10R-XCX-XXX
35.2 lbs (16.0 kgs)
. . . . . .
PX10R-XHX-XXX
39.6 lbs (18.0 kgs)
. . . . . .
PX10R-XSX-XXX
38.2 lbs (17.3 kgs)
. . . . . . .
add 4.65 lbs (2.11 kg) for Aluminum air motor section
add 11.09 lbs (5.03 kg) for Stainless Steel air motor section
Maximum Air Inlet Pressure
120 p.s.i.g. (8.3 bar)
. . . . . . . . .
Maximum Material Inlet Pressure
10 p.s.i.g. (0.69 bar)
. . . . .
Maximum Outlet Pressure
120 p.s.i.g. (8.3 bar)
. . . . . . . . . .
Maximum Flow Rate
(
flooded inlet
)
52.2 g.p.m. (197.6 l.p.m.)
. . . .
Displacement / Cycle @ 100 p.s.i.g.
0.232 gal. (0.88 lit.)
. . .
Maximum Particle Size
1/8” dia. (3.3 mm)
. . . . . . . . . . . .
Maximum Temperature Limits (diaphragm / ball / seal material)
E.P.R. / EPDM
-60
_
to 280
_
F (-51
_
to 138
_
C)
. . . . . . . . .
Hytrel
R
-20
_
to 150
_
F (-29
_
to 66
_
C)
. . . . . . . . . . . . . .
Nitrile
10
_
to 180
_
F (-12
_
to 82
_
C)
. . . . . . . . . . . . . . .
Polypropylene
35
_
to 1
75
_
F (2
_
to
79
_
C)
. . . . . . . . .
Santoprene
R
-40
_
to 225
_
F (-40
_
to 107
_
C)
. . . . . . . . . .
PTFE
40
_
to 225
_
F (4
_
to 107
_
C)
. . . . . . . . . . . . . . .
Viton
R
-40
_
to 350
_
F (-40
_
to 177
_
C)
. . . . . . . . . . . . . .
Dimensional Data
see page 8
. . . . . . . . . . . . . . . .
Mounting Dimension
4” x 6.25” (101.6 mm x 158.8 mm)
. . . . . . . .
Noise Level
@ 70 p.s.i., 60 c.p.m.
80.6 db(A)
{
. . . . .
The pump sound pressure levels published here have been updated to an Equivalent
Continuous Sound Level (L
Aeq
) to meet the intent of ANSI S1.13-1971, CAGI-PNEU-
ROP S5.1 using four microphone locations.
NOTICE: All possible options are shown in the chart, however, certain
combinations may not be recommended, consult a representative or the
factory if you have questions concerning availability
.
Figure 1
MODEL DESCRIPTION CHART
P X 10 X - X X X - X X X
PX10X - XXX - X X X
637401 - X X
Diaphragm
Ball
FLUID SECTION SERVICE KIT SELECTION
EXAMPLE: Model # PD10A-ASP-AAA
Fluid Section Service Kit # 637401-AA
Seat Material
A - Santoprene
G - Nitrile
C - Hytrel
H - Hard 440 Stainless Steel
E - Carbon Steel
L - Hastelloy - C
F - Aluminum
S - 316 Stainless Steel
Diaphragm Material
A - Santoprene
M - Medical Grade Santoprene
C - Hytrel
T - PTFE / Santoprene
G - Nitrile
V - Viton
Hardware Material
P - Plated Steel
S - Stainless Steel
Fluid Caps & Manifold Material
A - Aluminum
H - Hastelloy - C
C - Cast Iron
S - Stainless Steel
Fluid Connection
A - 1 -- 11-1/2 N.P.T.F. - 1
B - 1 -- 11 BSP
Center Section Material
A - Aluminum
R - Polypropylene
S - Stainless Steel
Ball Material
A - Santoprene
S - 316 Stainless Steel
C - Hytrel
T - PTFE
G - Nitrile
V - Viton
Electronic Interface
D - None
E - Available
www.ingersollrandproducts.com
11-11-10
08)
