Ingersoll-Rand EBC180-300 Скачать руководство пользователя страница 22 | Manualshive

Страница: 22 / 40

Ingersoll-Rand EBC180-300 Скачать руководство пользователя страница 22

22

RT-SVX50F-EN

Pre Start

Verifying Proper Air Flow (Units
with Belt Drive Indoor Fan)

Much of the systems performance and reliability is closely
associated with, and dependent upon having the proper
airflow supplied both to the space that is being
conditioned and across the evaporator coil.
The indoor fan speed is changed by opening or closing the
adjustable motor sheave.
Before starting the SERVICE TEST, set the minimum
position setpoint for the economizer to 0% using the
setpoint potentiometer located on the Economizer Control
(ECA), if applicable.

Electromechanical Controls
Test Procedure

See unit schematic for correct wire numbers.

Fan Test and Minimum Ventilation.

Connect red

thermostat wire (R) to black thermostat wire (G).

Economizer Cooling.

Connect a jumper wire across

OAT on Economizer Control (ECA).

Connect red thermostat (R) wire to yellow thermostat wire
(Y1).

Cool 1.

Connect red thermostat wire (R) to yellow

thermostat wire (Y1).

Cool 2.

Connect red thermostat wire (R) to yellow

thermostat wire (Y2).

Heat 1.

Connect red thermostat wire (R) to brown

thermostat wire (W1).

Heat 2.

Connect red thermostat wire (R) to brown

thermostat wire (W2).

«
...
20
21
22
23
24
...
»

Содержание EBC180-300









































Отзывы:

Нет отзывов