Ingersoll-Rand Doosan HP675WCU-T3 Скачать руководство пользователя страница 83

Страница: 83 / 99

Fault Finding

Operation & Maintenance Manual

Book 22826226

Safety valve
operates.

Operating pressure too
high.

Check the setting and operation of the
regulator valve piping.

Incorrect setting of the
regulator.

Adjust the regulator.

Faulty regulator.

Replace the regulator.

Inlet valve set
incorrectly.

Refer to

SPEED AND PRESSURE

REGULATION ADJUSTMENT

in the

MAINTENANCE

section of this manual.

Loose pipe/hose
connections.

Check all pipe/hose connections.

Faulty safety valve.

Check the relieving pressure. Replace the
safety valve if faulty.

DO NOT ATTEMPT A

REPAIR

Oil is forced back
into the air filter.

Incorrect stopping
procedure used

Always employ the correct stopping
procedure. Close the discharge valve and
allow the machine to run on idle before
stopping.

Faulty inlet valve.

Check for free operation of the inlet valve(s).

Machine goes to full
pressure when
started.

Faulty load valve.

Replace the valve.

Machine fails to
load when the load
button is pressed.

Faulty load valve.

Replace the valve.

FAULT

CAUSE

REMEDY

Содержание Doosan HP675WCU-T3




































































































Результаты поиска

Содержание Doosan HP675WCU-T3

Отзывы:

Похожие инструкции для Doosan HP675WCU-T3

Бренды по названию

Популярные бренды

Ingersoll-Rand Doosan HP675WCU-T3, Руководство по эксплуатации и техническому обслуживанию

Результаты поиска

Содержание Doosan HP675WCU-T3

Отзывы:

Похожие инструкции для Doosan HP675WCU-T3

Бренды по названию

Популярные бренды