background image

Page 6 of 8 

PF20X-XXX-XXX-B (en)

PARTS LIST / PF20X-XXX-XXX-B AIR SECTION

  Indicates parts included in 637421 Air Section Service Kit shown below and items (70), (144), (175), (180) shown on page 4.

AIR MOTOR SECTION SERVICE

Service is divided into two parts - 1. Pilot Valve, 2. Major 

Valve.

GENERAL REASSEMBLY NOTES:

 

y

Air motor section service is continued from fluid section 

repair.

 

y

Inspect and replace old parts with new parts as neces-

sary. Look for deep scratches on metallic surfaces, and 

nicks or cuts in “O” rings.

 

y

Take precautions to prevent cutting “O” rings upon instal-

lation.

 

y

Lubricate “O” rings with Lubriplate FML-2 grease.

 

y

Do not over-tighten fasteners, refer to torque specifica-

tion block on view.

 

y

Re-torque fasteners following re-start.

 

y

Service Tools - To aid in the installation of (168) “O” rings 

onto the (167) pilot piston, use tool #204130-T, available 

from ARO.

PILOT VALVE DISASSEMBLY

1.  A light tap on (118) should expose the opposite (121) 

sleeve, (167) pilot piston and other parts.

2.  Remove (170) sleeve. Inspect inner bore of sleeve for 

damage.

PILOT VALVE REASSEMBLY

1.  Clean and lubricate parts not being replaced from service 

kit.

2.  Install new (171 and 172) “O” rings. Replace (170) sleeve.

3.  Install new (168) “O” rings and (169) seal - Note the lip di-

rection. Lubricate and replace (167) pilot piston.

4.  Reassemble remaining parts. Replace (173 and 174) “O” 

rings.

MAJOR VALVE DISASSEMBLY

1.  Remove (135) valve block and (233) adapter plate, expos-

ing (166 and 132) gaskets and (176) checks.

2.  Remove (233) adapter plate, releasing (140) valve insert, 

(141) valve plate, (199, 200 and 241) gaskets and (243 and 

244) “O” rings.

3.  Remove (136) plug and (137) “O” ring, releasing (111) 

spool.

MAJOR VALVE REASSEMBLY

1.  Install new (138 and 139) “U” cups on (111) spool - 

LIPS 

MUST FACE EACH OTHER

.

2.  Insert (111) spool into (135) valve lock.

3.  Install (137 and 242) “O” rings on (136) plug and assemble 

plug to (135) valve housing, securing with (105) screws.

4.  Install (140) valve insert, (141) valve plate, (199) gasket 

and (243 and 244) “O” rings into (135) valve housing. 

NOTE:

 Assemble (140) valve insert with “dished” side to-

ward (141) valve plate. Assemble (141) valve plate with 

part number identification toward (140) valve insert.

5.  Assemble (200 and 241) gaskets and (233) adapter plate 

to (135) valve housing, securing with (240) screws.

6.  Assemble (132 and 166) gaskets and (176) checks to (101) 

center body.

7.  Assemble (135) valve housing and components to (101) 

center body, securing with (134) screws.

AIR MOTOR PARTS LIST

Item Description 

(size)

(Qty) Part No.

[Mtl]

Item Description 

(size)

(Qty) Part No.

[Mtl]

101 Center Body 

(PF20A-X-X-B)

(1) 97031

[A]

                            

(PF20S-X-X-B)

(1) 97040

[SS]

103 Bushing

(1) 97394

[D]

105 Screw 

(M6 x 1 - 6g x 20 mm)

(4) 95887

[SS]

111 Spool

(1) 95651

[D]

118 Actuator Pin

 (0.250” x 2.276” long)

(2) 94083

[SS]

121 Sleeve

(2) 94084

[D]

126 Plug

(1) Y17-13-S

[SS]

`

127 90 St. Elbow 

(1-1/2 - 11-1/2 NPT)

(1) 94860

[C / I]

128 Set Screw 

(1/4” - 20 x 1/4”)

(2) Y29-42-S

[SS]

132 Gasket

(1) 94099

[B]

133 Lockwasher 

(1/4”) (PF20A-X-X-B)

(3) Y117-416-C [C]

                                     

(PF20S-X-X-B)

(3) Y14-416-T [SS]

134 Screw 

(M6 x 1 - 6g x 35 mm)

(4) 95923

[SS]

135 Valve Housing

 (PF20A-X-X-B)

(1) 96334-1

[A]

                                              (PF20S-X-X-B)

(1) 96337-1

[SS]

136 Plug

 (PF20A-X-X-B)

(1) 96335

[A]

               (PF20S-X-X-B)

(1) 96339

[SS]

137 “O” Ring 

(1/16” x 2” OD)

(1) Y325-32

[B]

138 “U” Cup 

(3/16” x 1.792” OD)

(1) 95966

[B]

139 “U” Cup

 (3/16” x 1-1/4” OD)

(1) Y186-50

[B]

140 Valve Insert

(1) 95650

[Ck]

141 Valve Plat

e

(1) 95659

[Ck]

146 “O” Ring 

 

(3/32” x 1-1/16” OD)

(1) Y325-118

[B]

147 “O” Ring

 

● 

(1/8” x 1/2” OD)

(2) Y325-202

[B]

166 Track Gasket 

(1) 94026

[B]

167 Pilot Piston

 (includes 168 and 169)

(1) 67164

[D]

168 “O” Ring

 (3/32” x 5/8” OD)

(2) 94433

[U]

169 “U” Cup

 (1/8” x 7/8” OD)

(1) Y240-9

[B]

170 Piston Sleeve

(1) 94081

[D]

171 “O” Ring 

(3/32” x 1-1/8” OD)

(1) Y325-119

[B]

172 “O” Ring 

(1/16” x 1-1/8” OD)

(1) Y325-22

[B]

173 “O” Ring 

(1/16” x 1-3/8” OD)

(2) Y325-26

[B]

174 “O” Ring

 (1/8” x 1/2” OD)

(2) Y325-202

[B]

176 Diaphragm

 (check valve)

(2) 94102

[SP]

199 Track Gasket

(1) 95666

[B]

200 Gasket

(1) 95665

[B]

`

201 Muffler

(1) 94810

201 Muffler 

(Optional)

(1) 94117

233 Adapter Plate 

(PF20A-X-X-B)

(1) 96336

[A]

                               

(PF20S-X-X-B)

(1) 96338

[SS]

240 Screw 

(M6 x 1 - 6g x 16 mm)

(2) 95991

[SS]

241 Track Gasket

(1) 96344

[B]

242 “O” Ring 

(1/16” x 7/32” OD)

(1) Y325-5

[B]

243 “O” Ring 

(1/8” x 5/8” OD)

(1) Y325-204

[B]

244 “O” Ring 

(1/8” x 7/8” OD)

(1) Y325-208

[B]

Lubriplate FML-2 Grease

(1) 94276

Lubriplate Grease Packets (10)

637308

● 

Used on models PF20S-XXX-SXX-B only.

◆ 

Used on models PF20A-XXX-SXX-B only.

`

 

Items not shown

Содержание ARO PF20 B Series









Отзывы: