background image

MS-SVX039A-EN

31

Warranty For Trane C-Series Ductless Systems and Related Accessories

Warranty For Trane C-Series Ductless Systems and 
Related Accessories

Products Covered

This warranty is extended by Trane, and applies to all Trane C-Series Ductless Systems and 
Accessories for these products which are sold by Trane and applied in accordance with Trane 
specifications.

Basic Warranty

The warrantor warrants for a period of 5 years from the initial start-up or 5 years and 6 months from 
date of shipment, whichever is less, against failure due to defects in material and manufacture and 
that it has the capacities and ratings set forth in Company's catalogs and bulletins ("Warranty").

If any part of your C-Series Ductless System fails because of a manufacturing defect under normal 
use and maintenance within the Limited Warranty Period, the Company will furnish the required 
replacement part. If the compressor, outdoor coil or indoor coil should be the part that fails during 
the Limited Warranty Period, the affected unit will be replaced. The purchaser must pay for any and 
all shipping and handling charges and other costs of warranty service for the replacement part 
including, but not limited to, any related service labor, diagnosis calls and refrigerant.

Exclusions and Limitations

Exclusions from this Warranty include damage or failure arising from: wear and tear; corrosion, 
erosion, deterioration; modifications made by others to the Equipment; repairs or alterations by 
a party other than Company that adversely affects the stability or reliability of the Equipment; 
vandalism; neglect; accident; adverse weather or environmental conditions; abuse or improper 
use; improper installation; commissioning by a party other than Company; unusual physical or 
electrical or mechanical stress; operation with any accessory, equipment or part not specifically 
approved by Company; refrigerant not supplied by Company; and/or lack of proper maintenance 
as recommended by Company. Company shall not be obligated to pay for the cost of lost 
refrigerant or lost product. Company's obligations and liabilities under this Warranty are limited to 
furnishing replacement equipment or parts, at its option, FCA (Incoterms 2000) factory or 
warehouse (f.o.b. factory or warehouse for US domestic purposes) at Company-designated 
shipping point, freight-allowed to Company's warranty agent's stock location, for all non-
conforming Company-manufactured Equipment (which have been returned by Customer to 
Company. Returns must have prior written approval by Company and are subject to restocking 
charge where applicable. Equipment, material and/or parts that are not manufactured by Company 
are not warranted by Company and have such warranties as may be extended by the respective 
manufacturer. 

COMPANY MAKES NO REPRESENTATION OR WARRANTY, EXPRESS OR IMPLIED, 

REGARDING PREVENTION OF MOLD/MOULD, FUNGUS, BACTERIA, MICROBIAL GROWTH, OR 
ANY OTHER CONTAMINATES.

 No warranty liability whatsoever shall attach to Company until 

Customer’s complete order has been paid for in full and Company's liability under this Warranty 
shall be limited to the purchase price of the Equipment shown to be defective. EXCEPT FOR 
COMPANY’S WARRANTY EXPRESSLY SET FORTH HEREIN, COMPANY DOES NOT MAKE, AND 
HEREBY EXPRESSLY DISCLAIMS, ANY WARRANTIES, EXPRESS OR IMPLIED CONCERNING ITS 
PRODUCTS, EQUIPMENT OR SERVICES, INCLUDING, WITHOUT LIMITATION, ANY WARRANTY 
OF DESIGN, MERCHANTABILITY OR OF FITNESS FOR A PARTICULAR PURPOSE, OR OTHERS 
THAT ARE ALLEGED TO ARISE FROM COURSE OF DEALING OR TRADE.

Additional warranty protection is available on an extra-cost basis and must be in writing and 
agreed to by an authorized signatory of the Company. Additional terms and conditions of warranty 
coverage are applicable for refrigeration equipment. If you wish further help or information 
concerning this warranty, contact: Trane—Warrantor, 2701 Wilma Rudolph Blvd., Clarksville, TN. 37040.

Содержание 4MUC4518A10N0A

































Отзывы: