background image

3

HB Series Desiccant Dryer Models 150-8000

ingersollrandproducts.com

5.1 INSPECTION

Upon receiving your Ingersoll Rand air dryer, please inspect the unit
closely.  If rough handling has been detected, please note it on your
delivery receipt, especially if the dryer will not be immediately uncrated.
Obtaining the delivery person's signed agreement to any noted
damages will facilitate any insurance claims

5.2 UNPACKING AND HANDLING

A

WARNING

Under no circumstances should any person attempt to lift heavy
objects without proper lifting equipment (i.e., crane, hoist, slings or fork
truck).  Lifting any unit without proper lifting equipment, can cause
serious injury.

5.0 RECEIVING AND INSPECTION

Refer to the General Arrangement drawing for the appropriate means for
lifting or moving the dryer.  When lifting the dryer, ensure that no stress
is applied to the piping or valving.  Refer to Section 10.2 for locating and
mounting of dryer.

6.0 SAFETY AND OPERATION PRECAUTIONS

Because an air dryer is pressurized and contains rotating parts, the
same precautions should be observed as with any piece of machinery
of this type where carelessness in operation or maintenance could be
hazardous to personnel.  In addition to obvious safety rules that should
be followed with this type of machinery, safety precautions as listed
below must be observed:

1. 

 

Only qualified personnel shall be permitted to adjust, perform
maintenance or repair this air dryer.

2.  Read all instructions completely before operating unit.

3.  Pull main electrical disconnect switch and disconnect any separate

control lines, if used, before attempting to work or perform maintenance
on the unit.

4.  Do not attempt to service any part while machine is in an operational

mode.

5.  Do not attempt to remove any parts without first relieving the entire air

system of pressure.

6.  Do not operate the dryer at pressures in excess of its rating.

7.  Do not operate the dryer without guards, shields and screen in place.

8.  Inspect unit daily to observe and correct any unsafe operating conditions.

OSHA

Heading Descriptions

A

WARNING

“Warning” is used to indicate a hazardous situation which has some
probability of death or severe injury. Warning should not be considered
for property damage accidents unless personal injury risk is present.

A

CAUTION

“Caution” is used to indicate a hazardous situation which may result in
minor or moderate injury.

A

NOTICE

“Notice” is used to indicate a statement of company policy as the
message relates directly or indirectly to the safety of personnel or
protection of property. Notice should not be associated directly with a
hazard or hazardous situation and must not be used in place of
“Danger,” “Warning,” or “Caution.”

A

NOTICE

The user of any air dryer manufactured by Ingersoll Rand, is hereby
warned that failure to follow the above Safety and Operation
Precautions may result in personal injury or equipment damage.
However, Ingersoll Rand does not state as fact, nor does it mean to
imply, that the preceding list of Safety and Operating Precautions is all
inclusive, and further, that the observance of this list will prevent all
personal injury or equipment damage.

120.26 Dryer - Operation, Installation, Maintenance Manual, and Parts 

Содержание 150-8000




















































Отзывы: