Ingersoll-Rand 1000 Скачать руководство пользователя

Страница: 18 / 32

Nirvana Cycling Refrigerated Dryer Models 1000-1600

ingersollrandproducts.com

10.0 TECHNICIAN MODE

SET

AUTO RESTART: Y

Depressing the SET button changes the AUTO RESTART

parameter from “N” to “Y”.

ENTER

AUTO RESTART: Y

Depressing ENTER saves the selected set point.

WARNING

Changing the AUTO RESTART feature to “Y” will

permit the dryer to operate automatically once power

is applied and after a brief delay. Proper warning

signs should be affixed to the dryer to alert users

and service personnel that dryer may start without

warning. Failure to do so may result in serious injury.

SELECT

DISPLAY

END TECH SET

PTS

Depressing the SELECT DISPLAY button displays the

END TECH SET PTS display.
The remaining non-adjustable parameters may be viewed by

depressing the SELECT DISPLAY button as required to arrive at

the desired display.

NOTICE

To exit the TECHNICIAN MODE at any time, depress

the button located above the SET button to return

to the CUSTOMER MODE.

10.2 ALARM LIST

At the end of the list of non-adjustable parameters, the

Microprocessor Control displays a list of the most recent 20

alarm conditions. This list can facilitate troubleshooting the

dryer.

SELECT

DISPLAY

BEGIN ALARM

LIST

At the end of the list of parameters, depressing the

SELECT DISPLAY button displays the beginning of the ALARM

LIST.

SELECT

DISPLAY

HPCO ALARM

Depressing the SELECT DISPLAY button displays the

alarms that the dryer has experienced, with the most recent

alarm displayed first. The actual display will depend on the

most recent alarm detected by the Microprocessor Control.

SELECT

DISPLAY

END ALARM LIST

The list of alarms can be scrolled by depressing the

SELECT DISPLAY button as needed. At the end of the alarm list,

the END ALARM LIST screen is displayed.

SELECT

DISPLAY

BEGIN ALARM

LIST

Depressing the SELECT DISPLAY list displays the

ALARM LIST screen at the top of the ALARM LIST.
The Alarm List will repeat as many times as the SELECT DISPLAY

button is depressed. To EXIT the ALARM LIST, perform the

following:

TECH SET MODE

Depressing the BLANK button (located above the SET

button) returns the controller to the top of the TECHNICIAN

MODE.

CHLLR TEMP: 37

Depressing the BLANK button again returns the

controller to the default display of the CUSTOMER MODE.

INTERNAL SALES ORDER# 81730430

DRYER PART NUMBER: NVC1000W400

PROJECT: Niagara Bottling,LLC_Kenosha, WI

Содержание 1000

































Результаты поиска

Содержание 1000

Отзывы:

Похожие инструкции для 1000

Бренды по названию

Популярные бренды

Ingersoll-Rand 1000, Руководство оператора

Результаты поиска

Содержание 1000

Отзывы:

Похожие инструкции для 1000

Бренды по названию

Популярные бренды