manualshive.com logo in svg

Ingecon SUN 125 TL U 208 Outdoor, Руководство по установке

Поделиться
Скачать
Ingecon SUN 125 TL U 208 Outdoor Скачать руководство пользователя страница 58

ABB2000IKI01

58

Installation manual

Ingeteam

17:05

24/06/12

MOD

17:05

24/06/12

MOD

17:05

24/06/12

17:05

24/06/12

5.6.6.  Synchronization kit

When several INGECON SUN Power TL U units are connected to the same medium voltage transformer, they must 
be synchronized.

Care must be taken to ensure the equipment is not live when accessing its interior.

The configuration of PV array voltages should be the same.

MPPTs connected by TL inverters to the same transformer should have the same voltage settings.

To synchronize INGECON SUN Power TL U units, a synchronization signal generator kit must be added, capable of 
synchronizing up to 6 units. 

In the following example, 4 INGECON SUN 125 TL U 208 Outdoor units are synchronized:

The following will have been needed:

• 

3 INGECON SUN 125 TL U 208 Outdoor inverters.

• 

1 INGECON SUN 125 TL U 208 Outdoor inverter and synchronization kit.

Given that the kit consists of a synchronization board and 6 fiber optic cables, factory fitted into the unit, the following 
will be needed when the synchronization is carried out:

• 

1 INGECON SUN 125 TL U 208 Outdoor inverter with the synchronization board fitted, connected via 1 

cable to its electronics block.

• 

3 cables to connect the synchronization card to the electronics blocks of the other three units. The connec-

tion of these 3 cables must be carried out by the installer.

• 

2 cables, included in the kit but not needed in this case.

The synchronization or synchronization repetition kits are to be found in the lower right-hand part of the pre-installed 
unit. Cables must lead from here to each of the electronics blocks which are to be synchronized.

The fibre optic cable is connected to the intake board of each of the electronics blocks as shown in the figure:

Содержание SUN 125 TL U 208 Outdoor

























































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды