Ingecon SUN 125 TL U 208 Outdoor Скачать руководство пользователя страница 57

Страница: 57 / 88

ABB2000IKI01

Installation manual

Ingeteam

5.6.4. Auxiliary services kit.

For the operation of the unit’s auxiliary services and some of the optional kits, a single-phase auxiliary supply is
needed at

~ 240

Vac 50/60 Hz, to be provided by the installer.

The purpose of this kit is to generate the necessary supply for the operation of the inverter’s auxiliary services, thus
avoiding the need to supply the unit externally.

This kit comprises a transformer with a suitable ratio for each model in the INGECON SUN Power U family.

Auxiliary service transformer

5.6.5. Voltage fall-out kit

This kit is supplied for cases where federal or national regulations require that the inverter be capable of withstanding
grid voltage fall outs.

For the operation of this kit activation via a display and additional hardware are required.

To configure it it is necessary to perform the following steps via the display:

17:05

24/06/12

Settings

17:05

24/06/12

Settings

17:05

24/06/12

Config change

17:05

24/06/12

Config change

17:05

24/06/12

17:05

24/06/12

17:05

24/06/12

Medium voltage connection

17:05

24/06/12

Medium voltage connection

Содержание SUN 125 TL U 208 Outdoor

























































































Результаты поиска

Содержание SUN 125 TL U 208 Outdoor

Отзывы:

Бренды по названию

Популярные бренды

Ingecon SUN 125 TL U 208 Outdoor, Руководство по установке

Результаты поиска

Содержание SUN 125 TL U 208 Outdoor

Отзывы:

Бренды по названию

Популярные бренды