Infopia LipidPro Скачать руководство пользователя страница 6

Страница: 6 / 30

• 10 •

• 11 •

LipidPro

Test Strip Information

LipidPro

Test Strip Information

Target to apply blood

Ribs that guide the
strip into the meter

Total Cholesterol

test area

HDL-Cholesterol

test area

Triglyceride

test area

This test strip is for glucose.

color-coding label

This test strip colored black enables to test
TC, HDL, TG and calculated LDL.

This test strip colored red is for Total
Cholesterol.

This test strip colored blue is for HDL-
Cholesterol.

This test strip colored green is for
Triglyceride.

The part for holding
strip

Confirmation
Window

Contact Bar

Front -

Back -

Front -

Back -

Front -

Back -

Front -

Back -

Front -

Back -

1. Lipid Profile test strip

Use only LipidPro

Test Strips with your LipidPro

meter.

5. Glucose test strip

2. Total Cholesterol test strip

3. HDL-Cholesterol test strip

4. Triglyceride test strip

Caution

1. Store the LipidPro

test strip vials in a cool and dry place. Keep out of direct

sunlight. Do not freeze.

2. Store test strips in their original vial only. Do not mix the test strips in new vials or in

any other container.

3. Immediately replace the vial cap and close tightly after picking out the

LipidPro

test strip.

4. Make a note of the discard date which is three months from the date you first open

a new vial of strips. Do not use LipidPro™ test strip and vial after the discard date.

5. Avoid getting dirt, food, and water on the test strip. Do not handle test strips with

wet hands.

6. Do not use the test strips after the expiry date printed on the package or vial since it

may cause inaccurate results.

7. Do not bend, cut, or alter the test strip.

8. LipidPro™ test strips are for single use only. Do not re-use.

9. Do not test at the following temperature condition:

- Lipid Profile strip : below 18

℃

(64

℉

) or above 30

℃

(86

℉

- glucose strip : below 10

℃

(50

℉

) or above 40

℃

(104

℉

)

10. Do not test with humidity below 10% or above 90%.

11. Refer to additional information in the LipidPro

test strip package.

12. Avoid getting dirt, food, and water on the color-coding label (backside of glucose

test strip).

13. Discard the used test strips carefully according to the local regulations.

Blood application and
Test area

Содержание LipidPro































Результаты поиска

Содержание LipidPro

Отзывы:

Похожие инструкции для LipidPro

Бренды по названию

Популярные бренды

Infopia LipidPro, Руководство пользователя

Результаты поиска

Содержание LipidPro

Отзывы:

Похожие инструкции для LipidPro

Бренды по названию

Популярные бренды