background image

 

SP-CEIL-012 

 

 

 

 

Page - 4 - 

Installation Manual 

Warning Statements 

 

WARNING: 

THE CEILING STRUCTURE MUST BE CAPABLE OF SUPPORTING AT LEAST FIVE (5) TIMES 
THE WEIGHT OF THE PROJECTOR. IF NOT, THE CEILING MUST BE REINFORCED. PROPER 
INSTALLATION PROCEDURE BY A QUALIFIED SERVICE TECHNICIAN, AS OUTLINED IN THE 
INSTALLATION INSTRUCTIONS, MUST BE ADHERED TO. FAILURE TO DO SO COULD RESULT 
IN SERIOUS PERSONAL INJURY, OR EVEN DEATH. 

 

 

WARNING: 

SAFETY MEASURES MUST BE PRACTICED AT ALL TIMES DURING THE INSTALLATION OF 
THIS PRODUCT. USE PROPER SAFETY GEAR AND TOOLS FOR THE INSTALLATION 
PROCEDURE TO PREVENT PERSONAL INJURY. 

 

 

WARNING: 

PRIOR TO THE INSTALLATION OF THIS PRODUCT, THE INSTALLATION INSTRUCTIONS 
SHOULD BE READ AND COMPLETELY UNDERSTOOD. THE INSTALLATION INSTRUCTIONS 
MUST BE READ TO PREVENT PERSONAL INJURY AND PROPERTY DAMAGE. KEEP THESE 
INSTALLATION INSTRUCTIONS IN AN EASILY ACCESSIBLE LOCATION FOR FUTURE 
REFERENCE. 

 
 

 

Indicates that the power plug is to be 
disconnected from the power outlet. 

 

 

Contact InFocus Corporation with any 
questions. 

 

 

 

 

 

 

Safety precautions must be taken at all 
times. 

 

 

 

 

 

 

 

 

 

Warning and Caution statements. 

 

 

 

 

 

A secure structure must support the weight, or load, of the projector. When mounting to a ceiling 
that contains wooden studs, dead center of the wooden stud must be confirmed prior to 
installation.  

 

 

 

Do not install on a structure that is prone to vibration, movement or chance of impact. Failure to 
do so could result in damage to the projector and/or damage to the mounting surface. 

 

 

 

Do not install near heater, fireplace, direct sunlight, air conditioning or any other source of direct 
heat energy. Failure to do so may result in damage to the projector and could increase the risk of 
fire. 

 

 

 

At least two qualified people should perform the installation procedure. Injury and/or damage can 
result from dropping or mishandling the projector. 

 

 

 

Recommended mounting surfaces: wooden studs and solid-flat concrete. If the mount is to be 
installed on any surface other than wooden studs, use suitable hardware (which is commercially 
available). 

Содержание SP-CEIL-012















Отзывы: