Infinity Modulus II Infinity, Руководство по обслуживанию

Страница: 13 / 35

MODULUS II HOME THEATER SYSTEM
Surround Modes
When using the Modulus II system in a Dolby Pro Logic* home
theater system, make sure the receiver’s center channel mode is
set to “Normal.” When using the Modulus II system in a Dolby
Digital or DTS home theater system, make sure the receiver’s
speaker modes are set to “Small.”
Some Dolby Digital-equipped receivers/processors offer different
setup options for each source or surround mode: e.g., CD-stereo,
videotape, Dolby, Pro Logic. In each case, follow your equipment’s
instructions to ensure that the subwoofer output is turned on and
that the speakers are set to “Small” in each mode.
Power On
Plug your Modulus II subwoofer’s AC cord into a wall outlet. Do not
use the outlets on the back of the receiver.
Initially set the subwoofer’s Level Control
ª
to the “O” position.
Turn on your sub with the Power Button
•
on the rear panel.
Auto On/Standby
With the Power Button
•
in the ON position, the Level Control
ª
on the front panel will remain backlit in red or green to
indicate the On/Standby mode of the subwoofer.
RED = STANDBY (No signal detected, Amp Off)
GREEN = ON (Signal detected, Amp On)
The subwoofer will automatically enter the Standby mode after
approximately 10 minutes when no signal is detected from your
system. The subwoofer will then power ON instantly when a signal
is detected. During periods of normal use the Power Button
•
can be left on. You may turn off the Power Button
•
during
extended periods of nonoperation: e.g., when you are away on
vacation.
Adjust Level
Turn on your entire audio system and start a CD or movie sound-
track at a moderate level. Turn your subwoofer’s Level Control
ª
up to the “5” position (half way). If no sound emanates from the
subwoofer, check the AC-line cord and input cables. Are the
connectors on the cables making proper contact? Is the AC plug
connected to a “live” receptacle? Has the Power Button
•
been
pressed to the “On” position? (Note: The Level Control
ª
on the
front panel will turn green when the power is on.) Once you have
confirmed that the subwoofer is active, proceed by playing a
sound source. Use a selection that has ample bass information.
Set the overall volume control of the preamplifier or stereo to a
comfortable level. Adjust the subwoofer’s Level Control
ª
until
you obtain a pleasing blend of bass. Bass response should not
overpower the room but rather be adjusted so there is a
harmonious blend across the entire musical range. Many users
have a tendency to set the subwoofer volume too loud, adhering
to the belief that a subwoofer is there to produce lots of bass.
This is not entirely true. A subwoofer is there to enhance bass,
extending the response of the entire system so the bass can be
felt as well as heard. However, overall balance must be maintained
or the music will not sound natural. An experienced listener
will set the volume of the subwoofer so its impact on bass
response is always there but is never obtrusive.
Phase Control
The Phase Switch
∞
determines whether the subwoofer
speaker’s piston-like action moves in and out with the main
speakers, 0˚, or opposite the main speakers, 180˚. Proper phase
adjustment depends on several variables such as room size,
subwoofer placement and listener position. Adjust the phase
switch to maximize bass output at the listening position.
Final Positioning
After correctly connecting the Modulus II system and verifying
that both the subwoofer and all satellite speakers are playing, it
is time to optimize the system for your particular listening room.
Earlier, you placed the subwoofer in its general location. Finding
the exact location for optimum performance sometimes only
involves moving the speakers up to a few inches in any direction.
We urge you, therefore, to experiment with placement, if possible,
until your speakers deliver their full potential.
O
PERATION
MSW-II