background image

What Does a Parametric Equalizer Do?

The R.A.B.O.S. system uses one band of parametric equalization
for response correction. Parametric equalizers are the most
versatile class of filters.The effect an equalizer will have on the
signal is dependent on three parameters.

Frequency:

The equalizer will have maximum effect at one

frequency, usually described as the center frequency.

Level:

This refers to the amount of cut (in dBs) the equalizer 

is set for.

Bandwidth:

Defines the range of frequencies over which the

equalizer will have an effect. On the Intermezzo, this adjustment
is abbreviated as “Width.”

Only parametric equalizers allow independent adjustment of all
three parameters.

These will be explained more fully in the sections that follow.

Completing the Measurement Template

Along the bottom of the Measurement Template are three fields
where you will enter the equalizer settings needed to complete
system optimization.

These instructions are based on the example in Figure 12. Use
this tutorial to become familiar with the process. Strategies for
several other test results will be presented later. After you have
completed these three entry fields, you will be ready to perform
the adjustments, completing R.A.B.O.S. optimization.

Frequency

The frequency of the R.A.B.O.S. equalizer may be adjusted to 
any one of nineteen frequencies from 20Hz to 80Hz. This defines
where you are going to apply equalization.

Width 

The frequency range of the R.A.B.O.S. equalizer may be set from
5% to 50% of an octave in 21 steps.This setting defines 
how much of the subwoofers’ output will be equalized.

Width is expressed as a percentage of an octave. For example, a
width setting of 25% means the equalizer will affect a frequency
band of 1/4 of an octave; 1/8 of an octave above and 1/8 of an
octave below the center frequency.

The octave is a logarithmic expression. From any point

in the spectrum, one octave above or below that point is always
double or half the frequency.Therefore, one octave above 100Hz
would be 200Hz. One octave below 100Hz is 50Hz.

In the section that follows, we will discuss the use of the 
Width Selector.

F

IGURE

13

Effect of adjustable width

12

INTERMEZZO 4.1t

Содержание Intermezzo 4.1t





























Отзывы: