3
INTERLUDE IL100
S
, IL120
S
If your receiver/processor does not have
subwoofer outputs for the left and right
channels or an LFE output:
C
ONNECTIONS
If your receiver/processor has subwoofer
outputs for the left and right channels:
NOTE: Some receivers have a single subwoofer output (do not
confuse this with a single LFE output as described below).
In that case, it is recommended that you use a Y connector
(not included) to maximize performance.
If you have a Dolby* Digital or DTS
®
receiver/
processor with a low-frequency-effect (LFE) output:
NOTE: In this case, you do not need to use a Y connector. Simply
connect the LFE output on your receiver/processor to either the left
or right input on the subwoofer.
+
+
+
+
–
–
–
–
L
In
Out
In
Out
POWER
3A 250V
Caution: For continued protection against risk of fire,
replace only with same type fuse and rating.
Attention: Utiliser un fusible de rechange
de meme type et calibre.
3A 120VAC 60Hz
Off
On
Right
Left
Input
Select
Low-Pass
Filter
Bass
Optimization
System
Phase
Low-Pass Freq. Adjust
80Hz
R
L
R
WARNING: SHOCK HAZARD • DO NOT OPEN
NO USER SERVICEABLE PARTS INSIDE
AVIS: RISQUE DE CHOC ELECTRONIQUE
NE PAS OUVRIR
ANSI/UL-1492
LR106476
On
50Hz
150Hz
Off
0
o
180
o
On
Off
Freq.
Level
Width
RECEIVER/AMPLIFIER
Front Speaker Output
Line Level
Speaker
Line
SPEAKER LEVEL
+
+
+
+
–
–
–
–
L
In
Out
In
Out
POWER
3A 250V
Caution: For continued protection against risk of fire,
replace only with same type fuse and rating.
Attention: Utiliser un fusible de rechange
de meme type et calibre.
3A 120VAC 60Hz
Off
On
Right
Left
Input
Select
Low-Pass
Filter
Bass
Optimization
System
Phase
Low-Pass Freq. Adjust
80Hz
R
L
R
WARNING: SHOCK HAZARD • DO NOT OPEN
NO USER SERVICEABLE PARTS INSIDE
AVIS: RISQUE DE CHOC ELECTRONIQUE
NE PAS OUVRIR
ANSI/UL-1492
LR106476
On
50Hz
150Hz
Off
On
Off
Freq.
Level
Width
RECEIVER/PROCESSOR
0
o
180
o
Line Level
Speaker
Line
SPEAKER LEVEL
SUBWOOFER OR
LFE OUTPUT
+
+
+
+
–
–
–
–
L
In
Out
In
Out
POWER
3A 250V
Caution: For continued protection against risk of fire,
replace only with same type fuse and rating.
Attention: Utiliser un fusible de rechange
de meme type et calibre.
3A 120VAC 60Hz
Off
On
Right
Left
Input
Select
Low-Pass
Filter
Bass
Optimization
System
Phase
Low-Pass Freq. Adjust
80Hz
R
L
R
WARNING: SHOCK HAZARD • DO NOT OPEN
NO USER SERVICEABLE PARTS INSIDE
AVIS: RISQUE DE CHOC ELECTRONIQUE
NE PAS OUVRIR
ANSI/UL-1492
LR106476
On
50Hz
150Hz
Off
180
°
0
°
On
Off
Freq.
Level
Width
Line Level
Speaker
Line
SPEAKER LEVEL
LOOSEN TERMINALS
INSERT BARE END;
TIGHTEN TERMINALS
1.
2.
BLACK =
–
NO STRIPE =
–
STRIPE =
+
RED =
+
• Set Input Selector to “Speaker.”
• Set Low-Pass Filter to “On.”
• Set Input Selector
to “Line.”
• Set Low-Pass
Filter to “On.”
• Set Input Selector
to “Line.”
• Set Low-Pass
Filter to “Off”.
