Infinity CLASSIA PSW310W Скачать руководство пользователя страница 22

Страница: 22 / 24

Infinity Classia

™

PSW310W

Frequency Response:

32Hz – 150Hz (–3dB)
28Hz – 150Hz (–6dB)

Amplifier RMS Power:

400 Watts RMS

Amplifier Peak Dynamic Power

†

700 Watts

Crossover Frequencies:

50Hz – 150Hz,
continuously adjustable when activated

Driver:

10" (250mm) CMMD

Dual 10" (250mm) CMMD passive radiators

RF Operating Frequency:

2.4GHz

Operating Range:

Up to 75' (22m),
depending upon conditions

Subwoofer Dimensions (H x W x D):

17-1/2" x 14" x 16-3/4"
(445mm x 356mm x 426mm)

Subwoofer Weight:

49.8 lb (22.6kg)

Transmitter Dimensions:

3-3/4" x 4-7/8" x 3-15/16"
(95mm x 124mm x 100mm)

Transmitter Weight:

0.5 lb (0.2kg)

†

The peak dynamic power is measured by recording the highest center-to-peak
voltage measured across the output of a resistive load equal to minimum impedance
of the transducer, using a 50Hz sine wave burst, 3 cycles on, 17 cycles off.

Features, specifications and appearance are subject to change without notice.

PECIFICATIONS

INFINITY CLASSIA PSW310W (120V)

Содержание CLASSIA PSW310W

























Результаты поиска

Содержание CLASSIA PSW310W

Отзывы:

Похожие инструкции для CLASSIA PSW310W

Бренды по названию

Популярные бренды

Infinity CLASSIA PSW310W, Руководство пользователя

Результаты поиска

Содержание CLASSIA PSW310W

Отзывы:

Похожие инструкции для CLASSIA PSW310W

Бренды по названию

Популярные бренды