background image

-27- 

 

S

 

Scheduling 

 

A Home Automation feature that switches HA units on and off 
automatically according to pre-set times. 

Sensors 

 

The devices installed around the home that alert the panel in the 
event of an alarm.  

Service Call 

 

A feature that enables the user to contact the monitoring service and 
talk to an operator via the control panel. 

SMS Command 

 

An SMS message sent to the control panel that causes the system to 
perfotm a specific function. 

SMS Confirmation 

  An SMS message sent to the user confirming that the SMS 

command has been performed. 

Stop 

Communications 

 

An operation that clears all communication buffers and stops the 
transmission of any pending messages to the monitoring service.  

System Status 

Indicators 

 

Luminous indicators on the front panel that provide information on 
the arm and power status of the system. 

T

 

Tones 

 

Chimes sounded by the control panel’s internal or external siren. 

TWA 

 

Two-Way Audio (abbr.) 

TX 

 Transmitter 

(abbr.) 

TX List 

 

A service feature that lists all the system’s registered transmitters, 
their last recorded status and signal strength. 

TX Test 

 

A service feature that displays the source of the last received 
transmission. 

U

 

Unbypass 

 

The restoral of a bypassed zone to its original state. 

User Code 

 

A four-digit code that grants access to certain system functions such 
as arming and disarming the system. 

User TWA Code 

 

A user code that enables Two-Way Audio communication. 

W

 

Walk Test 

 

A mode that enables sensors to be tested without generating an 
alarm. 

Z

 

Zone 

 

A protected area within the security system. 

Zone Bypassing 

 

See Bypassed Zone 

 

Содержание ZI250C




























Отзывы: