Infineon XC886CLM Скачать руководство пользователя страница 102 | Manualshive

Страница: 102 / 663

background image

XC886/888CLM

Flash Memory

User’s Manual

4-12

V1.3, 2010-02

Flash Memory, V 1.0

4.6

Error Detection and Correction

The 8-bit data from the CPU is encoded with an Error Correction Code (ECC) before
being stored in the Flash memory. During a read access, data is retrieved from the Flash
memory and decoded for dynamic error detection and correction.

The correction algorithm (hamming code) has the capability to:

•

Detect and correct all 1-bit errors

•

Detect all 2-bit errors, but cannot correct

No distinction is made between a corrected 1-bit error (result is valid) and an uncorrected
2-bit error (result is invalid). In both cases, an ECC non-maskable interrupt (NMI) event
is generated; bit FNMIECC in register NMISR is set, and if enabled via
NMICON.NMIECC, an NMI to the CPU is triggered. The 16-bit Flash address at which
the ECC error occurs is stored in the system control SFRs FEAL and FEAH, and can be
accessed by the interrupt service routine to determine the Flash bank/sector in which the
error occurred.

*

«
...
100
101
102
103
104
...
»

Содержание XC886CLM
























































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для XC886CLM

Бренд: 3Ware Страницы: 2

Бренд: TCS Basys Controls Страницы: 2

Бренд: Danfoss Страницы: 7

Бренд: YOKOGAWA Страницы: 20

UTAdvanced UT32A

Бренд: YOKOGAWA Страницы: 3

Бренд: J+J Страницы: 2

Бренд: Daihan Scientific Страницы: 11

Бренд: Zander Aachen Страницы: 75

Бренд: FASTRON. Страницы: 37

Бренд: Festo Страницы: 2

Бренд: SYCLOPE Страницы: 28

Бренд: HomeMatic Страницы: 38

RailBoss 4 Basic

Бренд: G-Scale Graphics Страницы: 22

Бренд: Interactive Technologies Страницы: 431

Бренд: Linear Technology Страницы: 6

COMPASS SC-RS 232

Бренд: BFT Страницы: 24

Бренд: Magnetek Страницы: 19

Бренд: Aruba Networks Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды