manualshive.com logo in svg

Inficon Sensistor ISH2000 HySpeed, Руководство по эксплуатации

Поделиться
Скачать
Inficon Sensistor ISH2000 HySpeed Скачать руководство пользователя страница 40

Hydrogen leak detector Sensistor ISH2000 

 - 

Operating Manual

40

OM-Sensistor ISH2000-EN-201304

EN

Only pin 2 (Received data), pin 3 (Transmitted data) and pin 5 (Signal ground) are 
used. Refer to Figure 8-5 for the wiring diagram.

Fig 8-6. D9 Null modem cable wiring diagram

Selectable printer types

Most PC-printers with serial interface can be connected to the 9-pin printer port. 
Parallel (Centronics) interface printer can be used if connected through a serial to 
parallel converter. 

The port can be set up for the following printer types: PC Printer and Data Dump.

No printer

Printer output disabled. Incoming communication is enabled. Sensistor ISH2000 
listens for incoming data but will not print/send test results.

PC printer (with serial interface)

The

 PC Printer

 option can be used to print data on most standard PC printer with 

serial interface. Parallel interface printers can be used if connected through a serial 
to parallel converter (see below).

Note:

The output format has been chosen to be as simple as possible to ensure that 
most printers will accept it. Therefore, the printer output does not use any 
flow control. This means that some printers may delay printing until the input 
buffer is full or a pre-defined timeout has elapsed.

Table 8-5. Communication specifications.

5

SG

Signal ground

6

(DSR)

Not used

7

(RTS)

Not used

8

(CTS)

Not used

9

+7 VDC

Power feed USB/RS232 converter

Pin

Signal

Comments

1

2

3
4

5

6

7
8

9

9

8

7

6

5

4

3

2

1

CD

CD

RxD

RxD

TxD

TxD

DTR

DTR

SG

SG

DSR

DSR

RTS

RTS

CTS

CTS

R1

R1

D9 Female

D9 Female

Setting

Value

Data rate

1200 baud

Data bits

8

Stop bits

1

Parity

None

Flow control

None

Содержание Sensistor ISH2000 HySpeed



























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды