manualshive.com logo in svg

Inficon Sensistor ISH2000 HySpeed, Руководство по эксплуатации

Поделиться
Скачать
Inficon Sensistor ISH2000 HySpeed Скачать руководство пользователя страница 11

Hydrogen leak detector Sensistor ISH2000

 - 

Operating Manual

 

OM-Sensistor ISH2000-EN-201304

11

EN

3.2   Push-buttons

The functions of the push-buttons are shown at the lower edge of the display. In this 
manual the buttons are numbered, from left to right, 1, 2, 3, and 4. The push-buttons 
are used to:
•

Change from one menu item to another using the 

< 

and 

>

 buttons.

•

Press 

Enter

 to move down to the nearest sub-menu.

•

Press 

Save

 to save the set value.

•

Press 

Undo

 to restore the previously set value.

•

Press 

Esc

 to move up to the nearest higher level(s).

•

Shortcut to reach functions as Volume Sensitivity (Sens), Calibration (Cal) and   
Menu.

3.3   LEDs

The two LEDs indicate the status of the instrument as follows:
•

Green flashing slowly, during warming up phase.

•

Green fixed light indicates that instrument is ready and hydrogen signal is below 
Reject Level limit.

•

Periodically flashing green or red calls for calibration. 

•

Alternating red and green light while the instrument establishes probe 
communication.

•

Red fixed light together with 

Reject

 on display means the instrument has detected a 

leak larger than the set Reject Level limit.

•

Red flashing rapidly, check message on screen. (See “Trouble-shooting” on 
page 49.)

3.4   Ports and connections

The ports and connections are shown in Figure 3-2 on the next page.

NOTICE!

Always connect all four wires to the Power connector to 
24VDC in order to operate. 

Содержание Sensistor ISH2000 HySpeed



























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды