Indmar Raptor JET SERIES Скачать руководство пользователя страница 37 | Manualshive

Страница: 37 / 82

background image

5-1

© 2016 Indmar Marine Engines

Section Five

ENGINE STARTING PROCEDURES

Before operating or maintaining the engine, review
“Safety” on page 1-1.

NOTICE

Current fuel injected engines are equipped with a feature
called “Smart Start.” When the key is advanced to the
START position, the starter will remain engaged and will
crank the engine for 8 seconds or until the engine starts,
whichever happens ﬁrst. This same feature will prevent
accidental engagement of the starter when the engine is
running.

NOTICE

Some boats are equipped with a pushbutton start
instead of a key switch. Pushing the start button is the
same function as turning the key to the start position.

HOW TO START YOUR ENGINE

1.

WARNING! Operate the bilge blower for at least
4 minutes.

Run the blower for 4 minutes to remove

explosive gasoline and battery fumes from the
engine compartment.

ON

BLOWER

OFF

INDM-A011

Figure 5.1 – Typical Blower Switch

2. Perform the Pre-Start Checks. Refer to Section 3.

3. Move the shift control lever to the NEUTRAL position.

Pull out the neutral safety lever (if equipped). Without
advancing the throttle lever, turn the starter key to
START position.

NOTICE

The throttle should be in the neutral position with the
neutral detent button on the shift control box pulled out.

«
...
35
36
37
38
39
...
»

Содержание Raptor JET SERIES



















































































Отзывы:

Нет отзывов

Похожие инструкции для Raptor JET SERIES

Бренд: Kohler Страницы: 116

Бренд: Northern Lights Страницы: 31

Бренд: Econex Страницы: 14

Бренд: GAPOSA Страницы: 2

Бренд: Bartec Varnost Страницы: 48

Бренд: Marcato Страницы: 42

Бренд: YS Страницы: 5

Бренд: AE Страницы: 4

Бренд: Wilesco Страницы: 2

Бренд: Wilesco Страницы: 4

Бренд: Wilesco Страницы: 4

Бренд: Wilesco Страницы: 4

Бренд: Wilesco Страницы: 4

Бренд: DETROIT Страницы: 116

Concept engines

Бренд: RB Страницы: 19

Бренд: Honda Страницы: 156

Бренд: Baumuller Страницы: 22

Бренд: Marine Power Страницы: 56

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды