background image

8-6

SECTION EIGHT

EXTENDED STORAGE

If you must store your boat for an extended period 
of time (more than normal off-season storage), 
additional procedures are required. The procedures for 
preparing for extended storage and recommissioning 
after extended storage are best accomplished by an 
authorized Indmar dealer.

Follow the normal procedures for off-season storage.

Recommissioning

1.  Follow the normal procedures for recommissioning 

after off-season storage.

2.  Remove and clean the fuel injectors and flush the 

entire fuel system.

3.  Install a new fuel filter.

4.  Change all of the engine fluids and lubricants. Install 

a new oil filter.

5.  Check all belts and hoses for cracks and wear. 

Replace as needed.

6.  Install new spark plugs. Check the wires for cracks 

and damage.

7.  Charge the battery and check battery connections to 

make sure they are clean and tight.

8.  Put fresh gasoline in the fuel tank that does not 

contain ethanol. Cycle the key switch several times to 
make sure the fuel system is full and primed. Install 
an appropriate tester and verify the fuel pressure is 
at specification.

9.  Apply water to the engine’s cooling system and start 

the engine. While the engine is warming up, check 
for leaks and smooth engine operation. Monitor the 
fuel pressure to make sure it stays in specification.

10. Put the boat in the water and operate it at various 

RPM. Monitor the engine temperature, oil pressure, 
charging voltage and fuel pressure to make sure all 
stay within specification. Check the various engine 
operating parameters with a diagnostic scan tool to 
make sure all parameters are within specification.

Содержание Raptor JET SERIES



















































































Отзывы: