background image

P

R

ODUCT

G

B

8

Language

English

Service Manual

Hobs - 2006

Edition

2006.03.13

Cooking zones technical description

Halogen elements 

This type of element transmits heat through irradiation 

of the internal halogen lamp. One of the main benefi ts 
of this type of element is that its properties are similar 
to a gas ring: fast response to control adjustments and 
instantly visible indication of heating power.

Radiant elements

This type of element is composed of multiple spi-

rals that ensure uniform distribution of heat on the 
base of the pan for perfect preparation of foods that 
require low heat such as stews, sauces, or when 
re-heating previously cooked foods.

Key:

H     =  single halogen cooking zone 
R     =  single radiant cooking zone
HD  =  double halogen cooking zone

Other types of connection

If the electrical system complies with one of the 

following characteristics:

Mains voltage, type and frequency

380V  + N ~ 50 Hz

230V 3 ~ 50 Hz

380V + 2N ~ 50 Hz

Connect the wires according to the following table 

and diagrams:

If the electrical system complies with one of the 

following characteristics:

Mains voltage, type and frequency 400V 3 - N ~ 50 

Hz, proceed as follows: 

The power cord supplied cannot be used for this 

type of installation. 

1.  Use a suitable power cord such as H05RR-F 

type or higher, of suitable size (cross section: 25 
mm).

2.  Use a screwdriver to press on the tabs that secu-

re the terminal board cover and open the cover 
(see fi gure showing Terminal board).

3.   Unscrew the cable clamp screw and the screws 

of the terminals in relation to the type of con-
nection required, positioning the jumpers in 
accordance with the information in the following 
table and diagrams

4.   Position the wires according to the following table 

and diagrams and secure the connections by 
tightening the terminal screws fully home.

5.  Secure the power cord in the specifi c cable  

 

 

clampand close the cover.

400V - 2+N ~

50 Hz

230V 3 ~

50Hz

L1: black
L2: brawn

400V - 2+2N ~

50 Hz

N1: blue

N2: blue

L1: black

L2: brown

Mains voltage, 

type and frequency

Power cord

Wires connection

: yellow/green;

: yellow/green;

N: the 2 blue wires 
together

COOKTOPS  

 

    TVL 641

Cooking zone 

 

    Power

Right-rear 

 

    R 1400 W

Right-front 

 

    H 1800 W 

Left-front 

 

    R 1200 W

Left-rear  

 

    HD 2500-1050 W

Total maximum power  

    7200 W

400V 3-N ~

50 Hz

Mains voltage, 

type and frequency

Wiring connections

Terminal board

Three-phase 400

5

1

2

3

4

Phase    Jumper        Phase   Phase  Neutral   Earth

Содержание TIL641






























Отзывы: