Indesit K 645 V.C/G, Инструкция по установке и эксплуатации

Страница: 5 / 16

5
inlet for the cookers is a threaded G 1/2 gas female fitting.
Connecting the gas supply
To make the connection, a flexible hose should be used
corresponding to the current gas regulations which are:
• the hose must never be at any point in its lenght in contact with
the “hot” parts of the cooker;
• the hose must never be longer than 1,5 metre;
• the hose must not be subject to any tension or torsional stress
and it must not have any excessively narrow curves or
bottlenecks;
• the hose must be easy to inspect along its entire length to check
its condition;
•
the hose must always be in good condition, never attempt to
repair.
Important: the installation must comply with gas safety (installation
and use) regulations 1984. In all cases for the above, by low, a
qualified, corgi approved engineer must be called for installation.
Electrial connection
Power supply voltage and frequency: 230-240V a.c. 50 Hz.
Note: the supply cable must be positioned so that it never reaches
at any point a temperature 50°C higher than the room temperature.
The cable must be routed away from the rear vents. Should you
require it, you may use a longer cable, however, you must ensure
that the cable supplied with the appliance is replaced by one of the
same specifications in accordance with current standards and
legislation.
Your appliance is supplied with a 13 amp fused plug that can be
plugged into a 13 amp socket for immediate use. Before using the
appliance please read the instructions below.
WARNING - THIS APPLIANCE MUST BE EARTHED.
THE FOLLOWING OPERATIONS SHOULD BE CARRIED OUT
BY A QUALIFIED ELECTRICIAN.
Replacing the fuse:
When replacing a faulty fuse, a 13 amp ASTA approved fuse to BS
1362 should always be used, and the fuse cover re-fitted. If the fuse
cover is lost, the plug must not be used until a replacement is obtained.
Replacement fuse covers:
If a replacement fuse cover is fitted, it must be of the correct colour
as indicated by the coloured marking or the colour that is embossed
in words on the base of the plug. Replacements can be obtained
directly from your nearest Service Depot.
Removing the plug:
If your appliance has a non-rewireable moulded plug and you should
wish to remove it to add a cable extension or to re-route the mains
cable through partitions, units etc., please ensure that either:
•
the plug is replaced by a fused 13 amp re-wireable plug bearing
the BSI mark of approval.
or:
• the mains cable is wired directly into a 13 amp cable outlet,
controlled by a switch, (in compliance with BS 5733) which is
accessible without moving the appliance.
Please note: for appliances with a rating greater than 13 amp (eg:
electric hob, double ovens and freestanding electric cookers etc.)
the mains cable must be wired into a cooker output point with a
rating of 45 amp. In this case the cable is not supplied.
Disposing of the plug:
Ensure that before disposing of the plug itself, you make the pins
unusable so that it cannot be accidentally inserted into a socket.
Instructions for connecting cable to an alternative plug:
Important: the wires in the mains lead are coloured in accordance
with the following code:
Green & Yellow - Earth
Blue - Neutral
Brown - Live
If the colours of the wires in the mains lead do not correspond with
the coloured markings identifying the terminals in your plug, proceed
as follows:
Connect Green & Yellow wire to terminal marked “E” or
or
coloured Green or Green & Yellow.
Connect Brown wire to terminal marked “L” or coloured Red.
Connect Blue wire to terminal marked “N” or coloured Black.
If a 13 amp plug (BS 1363) is used it must be fitted with a 13 amp
fuse. A 15 amp plug must be protected by a 15 amp fuse, either in
the plug or adaptor or at the distribution board. If you are in any
doubt about the electrical supply to your machine, consult a qualified
electrician before use.
How to connect an alternative plug:
The wires in this mains lead are coloured in accordance with the
following code:
BLUE
“NEUTRAL” (“N”)
BROWN “LIVE” (“L”)
GREEN AND YELLOW “EARTH” (“E”)
GREEN &
YELLOW
BROWN
BLUE
13 amp fuse
CROSS-BAR
CORD GRIP
Disposing of the appliance
When disposing of the appliance please remove the plug by cutting
the mains cable as close as possible to the plug body and dispose
of it as described above.
Adapting the cooker to different types of gas
In order to adapt the cooker to a different type of gas with respect
to the gas for which it was produced (indicated on the label
attached to the lid), follow these steps:
a) replace the hose holder mounted on the appliance with that
supplied in the bag of “cooker accessories”.
Important: the hose holder for liquid gas is marked 8, the hose
holder for methane gas is marked 13. Always fit the sealing
gasket.
b) Replacing the burner nozzles on the hob:
•
remove the grids and slide the burners from their housings;
•
unscrew the nozzles using a 7 mm socket spanner, and
replace them with nozzles for the new type of gas (see table
1 “Burner and nozzle characteristics”).
• replace all the components by repeating the steps in reverse
order.