background image

6:3 Replacing heater element:

Warning! Be sure to turn power off fi rst! 
Drain the tank from water.

Basic and Slim
Take off the plastic cover, unscrew the two screws at the 
sides and push the cover downwards. Dismantle 
the thermostat and the overheat protector from their brackets 
for better access on the Slim model.
On Basic they can be left in position during the operation.
Pull off the wires from the heating element tabs.

Loosen the centre nut, fi g. 11-A and take off the support, 
fi g. 11-B. Put on the nut again on the centre bolt for easier 
handling, easier to grab by hand. 
Push off

 the mounting fl ange and rubber gasket inwards, 

it will come out together with the heater element unit. Turn 
the heater element unit 90° to the left, the wire tabs shall 
point to the right. 
Twist the unit until the inner end hits the tank to the left. 
Pull out the heater element unit through the hole with the
left side fi rst.
Unscrew the heater element from the mounting fl ange. 
Mount the new heating element with new seal rings and a 
new big rubber gasket in the opposite order to the 
description above. The inner end of the heating element 
shall point slightly downwards after assembly.

Slim Square
The heating element unit is on the Square model fastened 
by six screws on a fl ange which is fastened into the tank.
It has a rubber gasket. See fi g. 11
First, pull off the wires from the heating element tabs. 
Loosen all six screws, the heating element unit including 
the fl ange can be pulled out. Note the position of the fl ange. 
The heating element is fastened on the fl ange with 
nuts. Unscrew the heating element from the mounting 
fl ange. Mount the new heating element with new seal 
rings and a new big rubber gasket in the same position 
as before.
 

7. Double heat exchanger, Basic 40 & 75 litres

.

Double heat exchanger water heaters have connections for 
the second heat exchanger located also on the front, side by 
side with ordinary heat exchanger connections.
See fi g. 4
Replacement of the heating element is made the same way 
as the description above.

+

+

Fig. 11

001021

B        A

pantherRVproducts.com

Содержание 602421B000003














Отзывы: