background image

Reversing your Shop Stop:

At some cutting stations it may be desirable to reverse

the stop surfaces of the INCRA Shop Stop. This allows

the Shop Stop to function as either an infeed or outfeed

stop at the router table, or on either side of the blade at a

chop saw or radial arm saw.
To reverse your Shop Stop, first move the micro adjust

screw to the opposite end of the gold stop cap and

tighten the nylon nut against the aluminum. Remove and

reverse the #10-32 x 3-

1

2

" machine screw that holds the

vertical stop arm to the red stop body. Replace the stop

arm on the opposite end of the stop body. Make sure the

indexing lip on the arm wraps around the front of the stop

body (Fig. 3) and that the arm is flat against the end of

the body. Tighten the machine screw. (Fig. 8)

#10-32 nylon

hex nut

Stop

body

Vertical

stop arm

Hex nut

slides into

T-slot on

vertical

stop arm

#10-32 x 1" 

micro adjust

screw

Stop cap

4

INCRA Woodworking Tools & Precision Rules

FIG. 9

FIG.  8  

Reversing the Shop Stop

#10-32 x 3 

1

2

machine screw

#10 flat washer

FIG. 10

#10-32 hex nuts

1

4

diameter

hole

#10-32 x 

3

4

machine screws

1

2

"

3

16

"

3

4

" or

more

Note:  

Should you ever remove the

micro adjust screw, make sure to

tighten the nylon nut against the

aluminum when replacing it. The

nylon nut keeps the micro adjust

screw from vibrating loose during

cutting operations.

Example of user-made

wooden stop surface

designed to position

boards with mitered ends

1

2

"

FIG.  11  

Customizing your stop

DETAIL 11A  

#10 

flat

washer

1

2

"

Customizing your Shop Stop:

By removing both the vertical stop arm and the

horizontal stop rod, user-made wooden stops

can be attached to the front face of the stop.

Youʼll find this feature useful when you want the

stop surface to match an odd-shaped wood

profile or a mitered board end. Fig. 11 describes

just one example of a user-made stop. By gluing

two pieces of wood together, an “L” shape can be

produced which can be cut to match the desired

profile and then screwed into the T-slot. The “L”

feature on the block can be glued on to protrude

up, down, in or out as desired.

Reversible

stop surface 

Note:

Whenever reversing

the Shop Stop, always make

sure the stop surface

selected (vertical arm or

horizontal rod) protrudes at

least

1

8

"

in front of the end

of the gold stop cap.

Otherwise taller workpieces

will be stopped by the gold

stop cap rather than the

selected stop surface.

Reversible

stop surface 

2"

Содержание Shop Stop









Отзывы: